Member Since: 11 Oct 2010
Location: there's no f in point
Posts: 2137
Wheelnut torques
Having just purchased a 1/2inch torque wrench thought I'd try it out on what I bought it for... checking the wheel nuts.
Backing one off then torquing to 140NM (is this correct?... from memory from earlier posts) seems really NOT tight. Doesn't take as much turning force to undo as I would have thought.
The nuts are obviously well over the 140NM, done by the tyre fitter when all four were replaced last year, but appreciate that they might overtighten them.
So is 140NM correct? Doesn't seem very tight IMO.
17th Jun 2011 5:21 pm
WOODY179
Member Since: 01 Jun 2005
Location: Chesterfield
Posts: 3646
140 NM is correct
17th Jun 2011 5:24 pm
Bodsy Site Sponsor
Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361
140Nm is def correct. Is your wrench calibrated (the Halfords Pro Advance ones are)
You need to undo them all, re-torque them, then drive a few miles, then check again. Bodsys Brake Bible
Clock/ SNOTM /3Flash / 4x4Info /BT Update /Service Reset/Error Codes / Gearbox Reset See It Here
17th Jun 2011 5:47 pm
NickJ
Member Since: 11 Oct 2010
Location: there's no f in point
Posts: 2137
Well, it's probably not the best in the world, it's a Draper. Got good reviews on Amazon, someone checked theirs against a calibrated one and it was only a shade out. I'd assume it would have been calibrated of sorts when it left the factory.
17th Jun 2011 6:08 pm
devonchilliman
Member Since: 03 Nov 2008
Location: Devon
Posts: 5224
Your not alone,ive recently bought a "calibrated" torque wrench,so tightened my wheel nuts to 140 n/m when I swapped my rims over & also thought that it doesn't feel very tight Www.devonchilliman.co.uk
17th Jun 2011 6:16 pm
NickJ
Member Since: 11 Oct 2010
Location: there's no f in point
Posts: 2137
Perhaps just worrying about nothing.
When doing wheel nuts in the past I usually tighten them up as much as I can (got one - actually three - of those extendable handle thingies), so may be they were overtight.
Just nowhere near as tight as the professional tyre fitters. And they must be correctly done. Surely?
17th Jun 2011 6:53 pm
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
In the scheme of things 140 Nm is a pretty high torque setting. Don't try such a high figure on an ordinary car!
17th Jun 2011 7:06 pm
NickJ
Member Since: 11 Oct 2010
Location: there's no f in point
Posts: 2137
Yeah I know, it took ages to wind the handle around to 140! but it doesn't take that much force to undo the nut though. That's what got me wonering if everything was okay.
17th Jun 2011 9:04 pm
amazing
Member Since: 05 Mar 2011
Location: chengdu
Posts: 1542
all torque
If I remember correctly my old 101 was only 70Nm.. I can almost get that with a gerber It is better to have and not need it then need and not have it.
Last edited by amazing on 20th Jun 2011 8:14 am. Edited 1 time in total
18th Jun 2011 3:20 am
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
Nick,
It sounds like you are still a bit concerned with the calibration of your torque wrench compared to what feels right. Presuming you don't have access to a calibration tool (few of us do) have you tried borrowing another torque wrench and doing a comparison?
I have 4 torque wrenches and one of them is a Draper (albeit a small one not suitable for a D3), but it still came with a cal certificate hidden in the paperwork.Land Rover - Turning Drivers into Mechanics Since 1948
Member Since: 11 Oct 2010
Location: there's no f in point
Posts: 2137
Robbie,
Nice avatar
I have a 3/8" torque wrench, which was 'free' with a socket set years ago. I checket the two against each other this morning. They both seemed about the same. Will try the experiment again though later on.
18th Jun 2011 11:22 am
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
Thank-you, it was your post that prompted its return - it's from my Pillow Torque collection. Land Rover - Turning Drivers into Mechanics Since 1948
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum