noidea
Member Since: 03 Jun 2008
Location: Perth
Posts: 99
![](templates/vbnew/images/spacer.gif)
![2008 Discovery 3 TDV6 S Auto Atacama Sand 2008 Discovery 3 TDV6 S Auto Atacama Sand](../images/veh/atacama_sand.gif)
|
Front Parking sensor position |
|
Can anyone please measure the front parking sensor for me. I just purchase the aftermerket sensor and wanna install it. With pictures even better.
Please help guys ! Thanks alot.
|
15th Jun 2008 2:35 am |
|
|
kuli0010
Member Since: 26 Mar 2008
Location: Lost
Posts: 25
![](templates/vbnew/images/spacer.gif)
![2007 Discovery 3 TDV6 GS Auto Java Black 2007 Discovery 3 TDV6 GS Auto Java Black](../images/veh/java_black.gif)
|
If you take the bumper off, there are markings on the inside as to where the sensors go
|
15th Jun 2008 9:13 am |
|
|
noidea
Member Since: 03 Jun 2008
Location: Perth
Posts: 99
![](templates/vbnew/images/spacer.gif)
![2008 Discovery 3 TDV6 S Auto Atacama Sand 2008 Discovery 3 TDV6 S Auto Atacama Sand](../images/veh/atacama_sand.gif)
|
cool, no worries. I hope the bumper is easy to take off ! Thanks
|
15th Jun 2008 9:20 am |
|
|
catweasel
Member Since: 05 May 2006
Location: Bundaleer
Posts: 4805
![](templates/vbnew/images/spacer.gif)
|
I'm geussing thats your next topic
|
15th Jun 2008 12:12 pm |
|
|
noidea
Member Since: 03 Jun 2008
Location: Perth
Posts: 99
![](templates/vbnew/images/spacer.gif)
![2008 Discovery 3 TDV6 S Auto Atacama Sand 2008 Discovery 3 TDV6 S Auto Atacama Sand](../images/veh/atacama_sand.gif)
|
LOL, well, if i can't take it off then that will be my next topic.....
|
15th Jun 2008 1:14 pm |
|
|
kuli0010
Member Since: 26 Mar 2008
Location: Lost
Posts: 25
![](templates/vbnew/images/spacer.gif)
![2007 Discovery 3 TDV6 GS Auto Java Black 2007 Discovery 3 TDV6 GS Auto Java Black](../images/veh/java_black.gif)
|
Here you go......
Front bumper removal – Discovery 3
1. Remove the upper grille and headlight units as per instructions in the owner manual and remove the towing eye cover
2. Remove all visible screws across the front of the bumper assy. Including one in each headlight recess.
3. Remove four torx head fasteners underneath the front of the vehicle and one either side holding the bumper to the wheelarch liner
4. remove one screw either side located in the headlamp recess
5.Remove three trim clips (remove the centre expander first, then the trim clip) from inside the wheel arch
6. remove the rearmost trip clip from the wheelarch liner,
7. Remove two screws from the rear of the wheelarch.
8. Pull away the wheelarch trim from the rearmost edge, at the front there are two toggle clips, which sometimes break off and the front edge of the trim is located in a slot in the bumper.
9. At the top edge of the bumper, there are two Torx fasteners, remove the lower one either side.
10. Push out the two plastic lugs from the locating hole in the wing, pull away the bumper moulding, equally at first, then drivers side so that it swings round to the passenger side, if you have headlamp washers, you’ll need to disconnect the pipe onto the washer bottle
|
15th Jun 2008 1:25 pm |
|
|
catweasel
Member Since: 05 May 2006
Location: Bundaleer
Posts: 4805
![](templates/vbnew/images/spacer.gif)
|
noidea wrote:LOL, well, if i can't take it off then I will use the search facility and find out
|
15th Jun 2008 2:10 pm |
|
|