Member Since: 06 Mar 2014
Location: Surrey
Posts: 1172
It's out with the old and in with the new at Anorak Towers, as I wave goodbye to my trusty D3. Just time for a quick side by side photo:
Click image to enlarge
With the D3 out of the way though, it's time to bring the D4 up to spec. Some of this has been achieved by adding parts removed from the D3 or, in one case, swapping parts between the two. So, minor stuff like the extended valve on the spare wheel, the RLD protector plate, the dog guard, boot mat and third row seats mat were all removed from the D3 before sale:
Click image to enlarge
It's a small detail, but I also retrieved and re-used my modified fixing studs for the tow electrics cover. They're one of the most useful mods I've done:
Click image to enlarge
The most involved task was swapping extended roof rails that I'd fitted to the D3 with the standard ones that came with the D4:
Click image to enlarge
Fitting details for the extended rails can be found HERE.
New parts fitted include a fixed tow bar and a cubby box fridge, more of which in another post.Darren
"You came in that thing? You're braver than I thought!" - Princess Leia
Last edited by LandRoverAnorak on 21st Jul 2024 8:26 pm. Edited 2 times in total
17th Jul 2016 4:38 pm
LandRoverAnorak
Member Since: 06 Mar 2014
Location: Surrey
Posts: 1172
Tow Trust TL1 Tow Bar
I spent this morning fitting a Tow Trust TL1 fixed tow bar. I was also expecting to be fitting towing electrics too, having asked the LR dealer to check whether they were fitted. I'd bought the kit from Dan at Duckworths and printed off a thread from here that gave good instructions for removing the rear bumper.
Imagine my surprise when I took off the tow electrics cover to discover that the 13 pin socket was already fitted :
Click image to enlarge
The TL1 kit is complete with tow ball, which I wasn't expecting, and clear, simple installation instructions:
Click image to enlarge
Click image to enlarge
First job is to fit the central body to the chassis receiver. With a smear of copper clip on the mating faces and locking pin, it went in cleanly and was soon locked in place:
Click image to enlarge
Next came the two side arms, which were initially just lightly bolted to the central body until all of the bolts were in place. The outer ends of the side arms are secured to the chassis rails with 130mm bolts and spacer tubes, that have to be fed into place within the chassis. All very easy.
Click image to enlarge
With all of the bolts suitable greased and tightend, the final task was to bolt on the supplied Alko compatible tow ball:
Click image to enlarge
I'm very impressed with the TL1. It's a substantial bit of kit that inspires confidence - more so than the OEM fixed bar.
We're now ready for the D4 to fulfil one of its' prime roles as a caravan tug.Darren
"You came in that thing? You're braver than I thought!" - Princess Leia
Last edited by LandRoverAnorak on 18th Mar 2024 6:32 pm. Edited 2 times in total
17th Jul 2016 4:56 pm
LandRoverAnorak
Member Since: 06 Mar 2014
Location: Surrey
Posts: 1172
Cubby Box Fridge
The other significant new part fitted today was a cubby box fridge, bought via Duckworths recent group buy:
Click image to enlarge
Fitting is relatively straightforward, although I did spend ages trying to get the centre console trim to line up properly again.
First step is to remove the cup holder moulding from the centre console and the trim panel from the front of the cubby box area. Both just pull up with a little bit of force. There are two metal friction clips on the trim panel that came off and had to be fished out of the void beneath:
Click image to enlarge
Next, remove two screws that secure the water shedder from beneath the cup holders. It's worth noting that the emergency release wire for the EPB is located under this panel. Remove a further two screws from the top corners of the moulding behind where the trim panel has been removed from. These are quite tricky to get to and the sides of the centre console trim may need to be eased outwards to provide access.
Remove the torx bolts from the lid hinges and pull off the silver hinge trims. I spent quite a while looking for hidden fixings here as these trims didn't want to let go. They need to be sort of twisted and pulled up to release them.
At this point, the existing cubby box interior can be lifted out. Ours has the USB supply to the lid, so there was also a bit of faffing with the cable grommet before it would come free.
Fitting the cubby box fridge is, as the saying goes, the reverse of this procedure, although it's also necessary to make the electrical connection. The feed from the car is hidden below the water shedder with the connector wrapped in a little foam sleeve. The matching plug on the fridge is tightly secured with cable ties, which need to be released to allow it to reach the car supply.
The fridge in position:
Click image to enlarge
And with everything back in place:
Click image to enlarge
There's a small switch on the front edge with an integral LED to turn the fridge on, which only works when the ignition is also on.Darren
"You came in that thing? You're braver than I thought!" - Princess Leia
Last edited by LandRoverAnorak on 18th Mar 2024 6:24 pm. Edited 1 time in total
17th Jul 2016 5:17 pm
VVS210
Member Since: 05 Aug 2015
Location: Hampshire
Posts: 509
Where did you source the yellow turn clips for the tow electrics cover please? - would be handy to get a couple for my D4 if they are readily available. Thanks.D4 - Stornoway Grey
D2 V8 - Zambesi Silver (rust free JDM import 😎)
FL2 - Sd4 HSE
110 Td5 DCPU - Bonatti Grey - sold
FL2 Td4 - Zambesi Silver - sold
D2 Td5 - Epsom Green - sold
F1 Td4 - Giverney Green - sold
90 300 Tdi - White – sold BIG mistake should have kept it!
F1 Td4 - written off by a taxi!
D1 300 Tdi - written off by a Fiesta...
D1 200 Tdi - sold
90 Turbo Diesel - sold
Ser 2a SWB - sold and glad I 'got rid'
Ser 2 SWB - sold but wish I still had it!
17th Jul 2016 7:23 pm
LandRoverAnorak
Member Since: 06 Mar 2014
Location: Surrey
Posts: 1172
I made them. Two small squares of thickish plastic Araldited into the slots of a standard pair and painted yellow Darren
"You came in that thing? You're braver than I thought!" - Princess Leia
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
It's a '13 plate XS in Aintree green:
was it a dealer or private sale?
All of a sudden, I'm going to have quite a lot of stuff for sale that was bought for my D3.
