Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
DISCO3.CO.UK > Maintenance & Mods (D4)

HELP! LED Light bar Fitting and Wiring
Post Reply  Down to end
Page 1 of 1
Danwalk201
 


Member Since: 28 Aug 2023
Location: Telford
Posts: 4

United Kingdom 2015 Discovery 4 3.0 SDV6 SE Tech Auto Aintree GreenDiscovery 4
HELP! LED Light bar Fitting and Wiring

Hi all,

I'm after some help, please. I am looking to purchase this light bar:

https://www.led-colight.com/products/colig...-white-drl

I will also purchase the wiring harness with it, but have no idea what it includes.

I am clueless when it comes to electrics so can someone please let me know exactly what I need to buy to have this wired up to come on with the high beam and also have a switch installed?

I will have someone to help me fit it, but I want to make sure I have everything I need to fit without having to get halfway through and realise I need to go and buy something else.

I have a 2015 D4 in the UK.

Any help is always greatly appreciated, thank you!

EDIT: Apologies, I've put this in the D3 section instead of D4, Admins feel free to move it if needed. Thanks

Daniel
  
Post #236037630th Jan 2024 12:14 pm
View user's profile Send private message View poster's gallery Reply with quote
Davethegeo
 


Member Since: 01 Oct 2015
Location: Edinburgh
Posts: 908

Scotland 2014 Discovery 4 3.0 SDV6 HSE Auto Corris GreyDiscovery 4

It doesn't look like the bit of wiring included in that kit is really what one would call a wiring harness. A harness for auxiliary lights should include at least a fuse, switch, relay and decent cable and connectors to connect to your battery and a feed for high beam.

Search for "Stedi" or "lightbar" on the forum and you will find some useful pages. I fitted a Stedi ST1K just over two years ago and I'm very pleased with it.
 D1 300Tdi - gone
D2 Td5 ES (Alive remapped...mmm) - sadly gone
D4 2012 SDV6 XS - Stolen
D4 2014 SDV6 HSE - Shiny


 
 
Post #236038830th Jan 2024 3:06 pm
View user's profile Send private message View poster's gallery Reply with quote
HairyFool
 


Member Since: 04 Jan 2023
Location: North Essex
Posts: 651

United Kingdom 2016 Discovery 4 3.0 SDV6 Landmark LE Auto ZanzibarDiscovery 4

Even with "low power" LEDs the supply should be fed via a fuse from a relay, not a great deal of difference between most you can buy on line.

Terminal codes are:

85 Coil
86 Coil
87 Normally Open (NO)
87a Normally Closed (NC) - not present on 4 pin relays
30 Common connection to NO & NC terminals

The coil is not polarity sensitive, one terminal fed from a tap off of the headlamp circuit but must be 12v. The other side of the coil has the switch linking down to ground.
 A visitor from the dark side, my other vehicle is an is still an EV. Strictly speaking its SWMBO.  
Post #236039730th Jan 2024 4:31 pm
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10652

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

How do you select the different colours and modes.

Keep turning off and on?
  
Post #236041530th Jan 2024 5:41 pm
View user's profile Send private message View poster's gallery Reply with quote
Danwalk201
 


Member Since: 28 Aug 2023
Location: Telford
Posts: 4

United Kingdom 2015 Discovery 4 3.0 SDV6 SE Tech Auto Aintree GreenDiscovery 4

I have no idea, I'm waiting for them to get back to me so I can ask them about it
  
Post #236043630th Jan 2024 8:08 pm
View user's profile Send private message View poster's gallery Reply with quote
Danwalk201
 


Member Since: 28 Aug 2023
Location: Telford
Posts: 4

United Kingdom 2015 Discovery 4 3.0 SDV6 SE Tech Auto Aintree GreenDiscovery 4

Davethegeo wrote:
It doesn't look like the bit of wiring included in that kit is really what one would call a wiring harness. A harness for auxiliary lights should include at least a fuse, switch, relay and decent cable and connectors to connect to your battery and a feed for high beam.

Search for "Stedi" or "lightbar" on the forum and you will find some useful pages. I fitted a Stedi ST1K just over two years ago and I'm very pleased with it.


Thanks for the help, I was hoping someone could point me in the direction of what I'll need in terms of fuses, relays etc as I have no idea what will actually be required. I've had a look at some other posts but there isn't really a clear answer.
  
Post #236043930th Jan 2024 8:16 pm
View user's profile Send private message View poster's gallery Reply with quote
KevinD3
 


Member Since: 05 Aug 2020
Location: Sutton Coldfield
Posts: 1270

England 2008 Discovery 3 TDV6 HSE Auto Stornoway GreyDiscovery 3

Hey Dan, so when we’re talking about loom you need something similar to this
https://www.ebay.co.uk/itm/141461245000?mk...media=COPY

Either pre-made or make it up yourself, you need the fuse for protection and obviously a switch to turn them on Very Happy
There’s a lot of debate been had around whether you can just wire them to your high beams or whether they should be independently switched, I’m with the latter, as you may not want to blind an oncoming driver every time you flash them to come at a junction.
 2008 HSE Stornoway Grey

My Wife thinks the D3 is a hobby, The D3 thinks the wife is 💕 
 
Post #236045730th Jan 2024 10:39 pm
View user's profile Send private message View poster's gallery Reply with quote
HairyFool
 


Member Since: 04 Jan 2023
Location: North Essex
Posts: 651

United Kingdom 2016 Discovery 4 3.0 SDV6 Landmark LE Auto ZanzibarDiscovery 4

Purely from looking at the photos I'm not sure these will work as you want.

The loom appears to be a 4 pole DT04 male-female lead. 2 pins pass through and 2 tap off to the yellow and white lead.

The pass through is heavier wire so most likely the power feed. The yellow/white lead would then be for a switch, probably a push to make button that each time you press it steps through the 3 light modes and off.

Still using a relay it would be possible to turn on with the main beams but it might remember the last mode used or always turn on in one specific mode.

The DT04 connector kits are available from eBay, £6 for the single 4 way plug
 A visitor from the dark side, my other vehicle is an is still an EV. Strictly speaking its SWMBO.  
Post #236046231st Jan 2024 12:10 am
View user's profile Send private message View poster's gallery Reply with quote
Danwalk201
 


Member Since: 28 Aug 2023
Location: Telford
Posts: 4

United Kingdom 2015 Discovery 4 3.0 SDV6 SE Tech Auto Aintree GreenDiscovery 4

KevinD3 wrote:
Hey Dan, so when we’re talking about loom you need something similar to this
https://www.ebay.co.uk/itm/141461245000?mk...media=COPY

Either pre-made or make it up yourself, you need the fuse for protection and obviously a switch to turn them on Very Happy
There’s a lot of debate been had around whether you can just wire them to your high beams or whether they should be independently switched, I’m with the latter, as you may not want to blind an oncoming driver every time you flash them to come at a junction.


Thanks Kevin Smile That's really helpful and will take a look.

Quote:
Purely from looking at the photos I'm not sure these will work as you want.

The loom appears to be a 4 pole DT04 male-female lead. 2 pins pass through and 2 tap off to the yellow and white lead.

The pass through is heavier wire so most likely the power feed. The yellow/white lead would then be for a switch, probably a push to make button that each time you press it steps through the 3 light modes and off.

Still using a relay it would be possible to turn on with the main beams but it might remember the last mode used or always turn on in one specific mode.

The DT04 connector kits are available from eBay, £6 for the single 4 way plug


I've spoken to their support and they have said the below:

Quote:
The package will come with the DT conversion cable

You can connect the yellow wire and white wire separately to your daytime running lights or signal lights, then you can control them separately with the daytime running lights or signal lights


Is this possible with regard to wiring up to the DRL? I'm not fussed about the Indicators. It looks like it comes with a DT conversation kit so won't need to buy one of those.
  
Post #23606021st Feb 2024 2:21 pm
View user's profile Send private message View poster's gallery Reply with quote
Davethegeo
 


Member Since: 01 Oct 2015
Location: Edinburgh
Posts: 908

Scotland 2014 Discovery 4 3.0 SDV6 HSE Auto Corris GreyDiscovery 4

I'm not sure what a DT conversion cable is, but in any case, you will just use the high beam lights to switch a relay which will then in turn switch on your shiny new LED lightbar.
The existing highbeam wiring will not be enough to power both the highbeams AND your lightbar hence the need for the lightbar to have its own power supply. I take power for my lightbar from the Stop Start battery.
If you connect the lightbar in parallel with the highbeam then at the very least, you will blow the highbeam fuse. At worst you will melt cables and burn out switches.

There are lots of posts on this forum about wiring in spotlights and driving lights so do have a read of them. Wouldn't want you to damage your existing wiring.
 D1 300Tdi - gone
D2 Td5 ES (Alive remapped...mmm) - sadly gone
D4 2012 SDV6 XS - Stolen
D4 2014 SDV6 HSE - Shiny


 
 
Post #23606221st Feb 2024 5:52 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site