Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate ·
Log In
|
- You are currently viewing DISCO3.CO.UK as a guest - Register to take part or Log In
Raf Verjans
Member Since: 14 Jan 2022
Location: Bilzen
Posts: 13
![](templates/vbnew/images/spacer.gif)
![2005 Discovery 3 TDV6 S Auto Tonga Green 2005 Discovery 3 TDV6 S Auto Tonga Green](../images/veh/tonga_green.gif)
|
Hi all
Close to desperation... The Webasto won't fire up, whatever I try.
GAP-IID tool:
- Fuel pump works (you hear the ticking sound & diesel comes out the tube that feeds the Webasto. Tested this with the primer procedure;
- Testing procedure: doens't heat up properly, just gets warm, but nevertheless completes the sequence and says the routine was succesfull;
WTT-software:
- Every individual component (exc. the fuel pump) works and can be tested;
- The fuel pump won't work with the testing procedure on the WTT-software;
- Doing a test routine and the cooling-down immediately starts: the WBH won't fire up
Readout gives this:
Fault 1: Metering pump interruption
State of fault: stored, actual
Code: 88h
Other stuff I did=
Reset by removal of the fuse: about 20 times
Keep firing it up with the IID-tool in the hope it will 'repair itself': about 10 times
I'm through my options here. Gone through all of the subjects and Robbies guide, but I can't seem to find a solution for this particular issue.
An answer or a link to a thread that has the solution would be helpful !
Thank you
Raf
|
15th Jan 2024 6:43 pm |
|
|
Worms
Member Since: 24 Sep 2023
Location: Highlands
Posts: 340
![](templates/vbnew/images/spacer.gif)
![2005 Discovery 3 TDV6 Base 7 Seat Auto Zambezi Silver 2005 Discovery 3 TDV6 Base 7 Seat Auto Zambezi Silver](../images/veh/zambezi_silver.gif)
|
I feel your pain! These are fantastic bits of kit and deeply frustrating, in equal measure.
The GAP Tool auxiliary heater test procedure times-out at a maximum of 300 seconds, which is not long enough for the FBH to really get up to temperature. I'm also not sure if it does the glow-plugs-on regime at shut down, which a working FBH does to burn off any residual fuel/soot at the end of the cycle.
I seem to remember having to clear the error codes on the WTT software before I could get mine to work on the WTT test routine. Fuse removal alone isn't enough to clear all the Webasto codes.
Having got mine to work on WTT Test and GAP test, it still wouldn't reliably fire-up on its own on cold mornings. I resorted to a timer and remote from eBay and it's been great ever since.
Others have reported good results from increasing the intake air-flow rate. Previously:
2010 FL2 TD4e GS
‘93 Defender 110 200TDi CSW - still got this, non-runner on SORN.
‘87 Defender 90 4 cyl Petrol
‘83 110 CSW V8 - best ever!
Range Rover 2-door V8 (not sure of year - 4-speed box and vacuum diff switch)
Series III SWB Diesel
|
15th Jan 2024 9:13 pm |
|
|
Raf Verjans
Member Since: 14 Jan 2022
Location: Bilzen
Posts: 13
![](templates/vbnew/images/spacer.gif)
![2005 Discovery 3 TDV6 S Auto Tonga Green 2005 Discovery 3 TDV6 S Auto Tonga Green](../images/veh/tonga_green.gif)
|
Thx - I’ve resetted faults theough the WTT-software, as well as the reset with the fuse, and through the IID-tool. Numerous times, but it won’t kick in.
Is there another way to perform a hard reset of the FBh, other than through the WTT-software ?
Also unplugged all the wiring of the FBH for 15 minutes.
|
15th Jan 2024 9:30 pm |
|
|
|
Posting Rules
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|
|
DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
|
|
DISCO3.CO.UK is independent and not affiliated to Land Rover.