You really need a 20 ton press, but apply heat around the knuckle joint then try pressing it out, I have known a few to use a sledge hammer to get them out.
Flack
10th Dec 2023 9:13 am
jp1
Member Since: 29 Jan 2020
Location: Cornwall
Posts: 17
Thanks Flack
I'll try heat and lump hammer next, i dont have a 20 ton press so hopefully that will work
If it doesn't, do you know if applying a bead of weld around the inner bearing would work in this case, this seems to be another method ive seen being used on thw web?
Not that i have a welding machine mind
such a pita the last stumbling block before re-assembly of the whole rear end suspension !
10th Dec 2023 11:19 am
jp1
Member Since: 29 Jan 2020
Location: Cornwall
Posts: 17
Definitely beyond any tool I have available. Applied lots of heat and hammered like crazy, no movement whatsoever.
Is this likely to be a service an independent garage might offer ? Called KwikFit (only place open today) and they aren't interested unless it's the whole job
Else only option is new knuckles or at the price for two, I could consider a 20ton press, but that seems a gamble I think.
10th Dec 2023 2:05 pm
HairyFool
Member Since: 04 Jan 2023
Location: North Essex
Posts: 686
Any local engineering firm that might have one you could call on?
The alternative is to heat the whole thing up again but to then use a freezer spray on the bearing race to try and sharply cool that down.A visitor from the dark side, my other vehicle is an is still an EV. Strictly speaking its SWMBO.
10th Dec 2023 2:30 pm
john watson
Member Since: 10 Nov 2011
Location: lanark
Posts: 970
How about a 3” grinder and grind out a groove then split with a cold chisel. Have done this before with inner races that won’t move. Just make sure you have safety glasses on. Off course assuming you have access for a 3” grinder.Once you have defeated the idiots any job is half done. Pity there are so many idiots to defeat.
10th Dec 2023 3:21 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5050
I use a 30 ton press and even then I've had to add heat as well to shift some of them. I'd be surprised if your 10 ton will get it moving even with heat. You could try as john watson suggests splitting with a decent quality chisel but be careful!yµ (idµ - eAµ) ψ=mψ
10th Dec 2023 3:47 pm
Breg90
Member Since: 04 Feb 2017
Location: Falkirk
Posts: 360
Run some weld around the inner diameter - it will shrink it. What do you have to loose!Series one 1949 - in bits, chassis is strapped to the ceiling in my garage (beside the canoe)
LR 90 - In bits
Disco 3 - currently in bits
10th Dec 2023 5:12 pm
jp1
Member Since: 29 Jan 2020
Location: Cornwall
Posts: 17
Thanks everyone, its of to a local workshop tomorrow where they have a 100 ton press.
If they can't press out I'll try the bead of weld and/or a die grinder, and if all fails i'll open walllet and get new knuckles which makes it a very expensive repair..but no choice at this point
10th Dec 2023 8:13 pm
jp1
Member Since: 29 Jan 2020
Location: Cornwall
Posts: 17
Update - took about 15 tons of pressure ....should have got a 20 ton press is moral of the story !!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
