Member Since: 23 Aug 2020
Location: Norwich
Posts: 14
HELP d3 tdv6 05 codes p0299-00 p006a-00
These codes keep putting my into a lower power mode I know it's turbo low boost pressure and map and MAF sensor correlation car has been to 2 experts who cannot find anything there are no holes splits slits Olin pipes it's been pressure tested and smoked tested and has been found to be fine I have even put a reconditioned turbo on her with no luck the map and MAF sensor have been changed and up until the last land rover specialist updated the ECU to the latest software version if I unplugged the MAF sensor my problems went away, but with the new software it still runs rubbish whether it's connected or not
Readings have been done and MAF and MAP appear to be reading as they should.on acceleration and deceleration and yes there is and awful amount of black smoke on acceleration sometimes to the point you cannot see behind... Someone must have suffered this before I see some of the posts and it's always a split somewhere but not in this case...
23rd Aug 2020 10:06 am
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5061
Hi and welcome. It would help if you could provide the vehicle model details and year of manufacture, you can add it into your profile. yµ (idµ - eAµ) ψ=mψ
23rd Aug 2020 3:03 pm
Fatty100lb
Member Since: 23 Aug 2020
Location: Norwich
Posts: 14
Thank you have changed my profile didn't know I could do that but it's a 55 plate disco 3 HSE 2.7tdv6
23rd Aug 2020 3:11 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5061
OK so have you checked the turbo actuator rod is moving freely? Also, what diagnostic tool are you using?yµ (idµ - eAµ) ψ=mψ
23rd Aug 2020 3:17 pm
Fatty100lb
Member Since: 23 Aug 2020
Location: Norwich
Posts: 14
Yes actuator moving nice and free was also on my last turbo ( new one was a recon) initial read was on a icarsoft lr2 but testing of the MAF map and confirmation has been on a snapon verus which my mates garage uses. We also have had all the intercooler pipes off to fully check for any holes and bypassed the intercooler to test if it was that.
23rd Aug 2020 3:24 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5061
In that case it seems you have a leak, and a big one at that so you'd think it should be obvious. Have you checked the inlet manifolds, plenum chamber, etc?yµ (idµ - eAµ) ψ=mψ
23rd Aug 2020 3:27 pm
Fatty100lb
Member Since: 23 Aug 2020
Location: Norwich
Posts: 14
I have for the obvious leaks yes my egr valves are blanked so throttle flap is removed. I did read in a forum for a Freelander 2 that he had a similar problem and it turned out To be O ring and an inlet gasket.
Not sure if the same is related to a tdv6 and not mechanically minded enough to start taking it apart so Monday will speak to my mate who can do this kind of thing... I would have thought any external leak would show up on the smoke test though.
23rd Aug 2020 3:34 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5061
Yes a leak "should" show up on the leak test, but sometimes on rare occasions the area leaking only does so under induction pressure.(ie the split opens)
I don't want to send you chasing your tail, but if all the external induction fittings are sound, including the intercooler, turbo, and associated pipework. Then the only other area left is the engine itself.
You may have to stick a camera into the injector ports to see if there's anything wrong on the compression side. (damaged valves or piston) Although it should throw an injector dtc if that were the case.
If you can get a snap shot of the engine live values and post them here something might jump out!yµ (idµ - eAµ) ψ=mψ
23rd Aug 2020 3:44 pm
Fatty100lb
Member Since: 23 Aug 2020
Location: Norwich
Posts: 14
Just been through injector issues with my lexus that was zero fun and expensive.. what values are you after map, MAF, boost pressure, injectors
23rd Aug 2020 3:48 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5061
This is what you should be seeing in a fully warmed up TDV6 running fine.(albeit I think this was an EU4 and taken on a winters day) but it should be similar.
Voltage ign key on 13.94v
Voltage from DC converter 48.62v
Volume control valve 21.87%
Throttle pedal angle 0%
Pedal sensor 1 voltage 0.75v
Pedal sensor 2 voltage 0.25v
Pressure cntrl valve 13.67%
Mass air flow sensor signal A 4 g/s
Intake air temp 24deg C
Internal ECU temp 35 degC
Input/output status fuel lift pump. ACTIVE
Input/output status fuel lift pump power monitor. ACTIVE
Boost pressure actuator Bank 1. 0.87%
Boost pressure adjustment 87%
Fuel rail temp before FMEM 60degC
Generator command 46.87%
Generator feedback 23.84%
Generator voltage set point 15.70v
Fuel pressure 23.09 MPa
Engine speed 516 rpm
Eng oil temp 77degC
Coolant temp 78degC
Cylinder balance offset:
Injectors 1. 103k.
Inj 2. 0.99k.
Inj 3. 0.84k.
Inj 4. 0.93k.
Inj 5. 0.98k.
Inj 6. 1.19k
Ambient temp 12 degC
Battery voltage 13.97v
Boost air temp 22.30degCyµ (idµ - eAµ) ψ=mψ
23rd Aug 2020 3:58 pm
Fatty100lb
Member Since: 23 Aug 2020
Location: Norwich
Posts: 14
Not sure how many of them are readable and if the icarsoft is ok for it these are screenshots from a video I know the injectors are well within the numbers you have given as they were all about the 1000 mark give or take these were as I was driving fyi
23rd Aug 2020 4:12 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5061
iCarsoft should give you most of that lot, but bring back whatever you can as a "last roll of the dice" before you have to start pulling it apart.yµ (idµ - eAµ) ψ=mψ
23rd Aug 2020 4:23 pm
Fatty100lb
Member Since: 23 Aug 2020
Location: Norwich
Posts: 14
I have uploaded some to YouTube links above I got another that the photos taken from still trying to upload
23rd Aug 2020 4:57 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5061
Remove the oil cap and engine top cover, and replace the oil cap. Check the pipework entering the manifolds at the "Y" junction behind the plenum chamber. Also, there are small breather tubes which go from each manifold to to the crankcase breather which sits behind the oil filter. These are prone to splitting and may be affecting the pressure loss.
The other thing which clearly is amiss is the MAF sensor readings. Check the wiring harness and connections. You could also while you're in there remove the MAP sensor and make sure it's clean. Do not poke anything into it if it's dirty. Use brake cleaner, or carb cleaner to dissolve any grime.yµ (idµ - eAµ) ψ=mψ
23rd Aug 2020 5:51 pm
Fatty100lb
Member Since: 23 Aug 2020
Location: Norwich
Posts: 14
Checked all the above even took the throttle body off and changed o-rings used gasket paste on all pipe joins and blanking plates and I still have the same codes 😩😩😩
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
