Member Since: 22 Sep 2010
Location: Notts.
Posts: 8227
Emergency DIY dipstick
Buy beg or borrow about 1.5mtre of curtain wire, the springy/stretch type available from any hardware DIY shop, remove the outer plastic covering, look at the end, it usually ends in a point when it is cut, if it is sharp just rub it on a stone to take the sharp point off, clean the wire thoroughly,
Take the cap off the engine oil extractor pipe and insert the pointed end of the curtain wire into the extractor pipe, when you meet any resistance push and twist the wire, you will find three places where this has to be done, when the wire will not go any further stick a band of electric tape round the wire(see photo)
Withdraw the wire and measure the distance from the bottom of the tape to the oil level, when full the distance should be 96cmtr when the engine is cold.
If you have any problems reading the distance lay the wire on a sheet of newspaper after extracting it.
Replace the extractor pipe cap.
Congratulations you have just made an emergency oil dipstick for a Discovery 4.
There is no reason I can see why pushed right down and fitted with a rubber “0” ring for a seal at the top and cut to length it cannot be left in position.It can when others can't,
It will when others won't,
It goes where others don't.
14th Mar 2020 8:43 am
DrRobH
Member Since: 10 Oct 2015
Location: Hampshire
Posts: 927
Visitor from fullfatrr.com
RR Vogue SE 2011 4.4 TDV8
1974 Lightweight
14th Mar 2020 8:50 am
James W
Member Since: 27 Mar 2008
Location: Riyadh, KSA
Posts: 3079
Simple ideas are the best!
If this could be made into a permanent fixture as you say but with an integrated cap, they would sell like hot cakes.D4 XS, gone, much loved, never forgotten
2018 FFRR SDV8 Autobiography - Gone to someone with less sense and more time to enjoy it
2016 Toyota Hilux Invincible - Liberating experience
14th Mar 2020 8:53 am
M3DPO
Member Since: 22 Sep 2010
Location: Notts.
Posts: 8227
Easy enough, just drill the existing cap out slightly smaller than the curtain wire and then screw the curtain wire into it and glue with epoxy resin. It can when others can't,
It will when others won't,
It goes where others don't.
14th Mar 2020 9:06 am
Gareth Site Moderator
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26774
I had thought about this. It would be interesting to know the measurements when the oil is recorded as needing a top up.
14th Mar 2020 9:09 am
M3DPO
Member Since: 22 Sep 2010
Location: Notts.
Posts: 8227
Whenever it is over 96cm cold It can when others can't,
It will when others won't,
It goes where others don't.
14th Mar 2020 9:12 am
Wicked
Member Since: 04 Sep 2018
Location: Christchurch
Posts: 4
Is that dimension of 96CM correct for a Discovery 4?
I've just tried it and I measure 36CM from the top of the dipstick hole to the top of the oil level. My dashboard oil gage is showing full. Just checking?
Dave
24th Apr 2020 2:51 pm
BBDisco3
Member Since: 23 Nov 2008
Location: Cheshire
Posts: 3646
Guess it's curtains if won't come out
24th Apr 2020 2:59 pm
DSL Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73085
You don’t have to be draped over the wing to use it.
24th Apr 2020 3:02 pm
BBDisco3
Member Since: 23 Nov 2008
Location: Cheshire
Posts: 3646
But you could get hooked on using it
Still a good idea though
24th Apr 2020 3:05 pm
cable
Member Since: 08 Jul 2012
Location: bristol
Posts: 175
I think you should pull yourselves together.
24th Apr 2020 4:29 pm
DSL Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73085
Best yet. ^^^^^
24th Apr 2020 4:35 pm
BBDisco3
Member Since: 23 Nov 2008
Location: Cheshire
Posts: 3646
Any one got a guaranteed way of removing Disco4 engine oil out of white net curtains.
I've an hour before SWMBO is home.
Thought a quick test and put it back again and she would never know
24th Apr 2020 4:36 pm
DSL Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73085
Just swap them for the nets in the spare room. That’ll give you time to think, and plan the funeral.
If it gets stuck, it'll light up the haberdashery I guess..
Dean
====================================
2011 D4 XS - OBD port protection, RLD spare wheel protector, All LED interiors lights, Timed Climate enabled, iiD tool paired.
2011 D4 Landmark - Stolen from same dealer before I paid for it
2011 D4 GS - Stolen whilst at dealer ... All LED interiors lights, DRLs, Spare Wheel protector.
1996 300Tdi - Eaten by tin worms
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
... All LED interiors lights, DRLs, Spare Wheel protector.
