Member Since: 15 Sep 2009
Location: leeds
Posts: 166
New fault codes never seen before
I've just had a funny fault happen on my d3 pulling out onto a large roundabout giving a boot full to get out it was like the handbrake had gone on even though it clearly had not. But the car just dropped all power then off it went again after changing my shorts and getting home I read the codes with my bad remap box and got.
So an anyone point me towards good news as the this cost me plenty this year so far and I'm still part way to fitting a full polybush kit so I assume that's nothing to do with it and I cannot find any reference on here to them either.
So can anyone help ??
15th Jul 2013 5:08 pm
jobster
Member Since: 08 Jul 2012
Location: Hilversum
Posts: 591
P062E - Fuel Injector Driver Circuit Performance Bank 2
Description The powertrain control module (PCM) continuously monitors the operation of the fuel injectors and corresponding circuitry for cylinders 2, 3, 5 and 8. When the short to ground or short to power condition for those cylinders is detected the PCM sets the DTC. Monitor the PIDs to determine which cylinder number has an injector or injector circuit concern.
Possible Causes Fuel injector 2, power or ground circuit short to ground in harness
Fuel injector 2, power or ground circuit short to voltage in harness
Fuel injector 3, power or ground circuit short to ground in harness
Fuel injector 3, power or ground circuit short to voltage in harness
Fuel injector 5, power or ground circuit short to ground in harness
Fuel injector 5, power or ground circuit short to voltage in harness
Fuel injector 8, power or ground circuit short to ground in harness
Fuel injector 8, power or ground circuit short to voltage in harness
Fuel injector
Powertrain control module (PCM)
Could be a stuck EGR or faulty HPFP too.RLD Sump Guard
GVIF & rear camera
New FBH via Dan
BAS Remap with IIDTool
15th Jul 2013 5:25 pm
Gerry9870
Member Since: 19 Apr 2020
Location: Coatbridge
Posts: 3
Re: New fault codes never seen before
johno1973 wrote:
I've just had a funny fault happen on my d3 pulling out onto a large roundabout giving a boot full to get out it was like the handbrake had gone on even though it clearly had not. But the car just dropped all power then off it went again after changing my shorts and getting home I read the codes with my bad remap box and got.
So an anyone point me towards good news as the this cost me plenty this year so far and I'm still part way to fitting a full polybush kit so I assume that's nothing to do with it and I cannot find any reference on here to them either.
So can anyone help ??
Hi matey
Appreciate it was a while ago, but did you ever get to the bottom of the PO62D /PO62E codes?
Cheers
Gerry
23rd May 2020 3:01 pm
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20742
Member Since: 19 Apr 2020
Location: Coatbridge
Posts: 3
PO62D
Mickey
No remap carried out
Injectors were working prior to removal
ECU was cloned, didnt make any difference
All from an inlet manifold replacement, 6 weeks now its not firing, did manage to coax it with easy start, but didnt run. sounds awfully rattly on trying to start.
23rd May 2020 4:15 pm
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1786
If it runs on "Easy Start" but not on fuel, then a possible pump problem or not enough fuel in tank. Rattle on start up is possibly timing chain adjusters
29th May 2020 5:54 am
Brianlee2793
Member Since: 23 Jan 2022
Location: Henderson
Posts: 1
Hey mate I know it's been a while. But has this ever been sorted?
20th Feb 2022 7:57 pm
Jdmrdisco
Member Since: 07 Dec 2022
Location: Somerset
Posts: 3
I've just had all my injectors out of my 2.7,
Correctly reseated with new oem injector washers,
I'm now having this same Po62e fault code.
I had to slide hammer the injectors out as they
Had all been chuffing a while by the looks of it.
Could this have damaged the injectors at all?
I was careful with the removal of the
solenoids and retained all the parts.
*I've checked for continuity between each injector
And the corresponding ecu pin. All 6 were fine.
*It's also worth noting I had to move the main bulk head
Loom to get access with the puller on one of the
rear injectors
*I cleaned up a couple pins on ecu and module situated infr9nt of it however vehicle ran really well(injectors chuffed) prior to doing the injectors
*Got good fuel supply to injectors.
*vehicle has a egr delete 2000miles ago
*stage 1 remap with egr delete 2000 miles ago
Any help with this would be greatly appreciated. As its my daily driver
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum