Member Since: 15 Oct 2020
Location: Wokingham
Posts: 412
12V Aux dimensions
Can anyone let me know what the hole dimensions are for the 12V Aux socket in the boot? Or alternatively, is it possible to remove the existing socket without removing the side panel?
I'm having a different connector made up to fit in there but I'd rather not take the whole boot apart and then put it together again just to measure the hole if I don't have to.
PM Andy Foster... I doubt there's any electrical connections inside the car he's not fettled with..
Dean
====================================
2011 D4 XS - OBD port protection, RLD spare wheel protector, All LED interiors lights, Timed Climate enabled, iiD tool paired.
2011 D4 Landmark - Stolen from same dealer before I paid for it
2011 D4 GS - Stolen whilst at dealer ... All LED interiors lights, DRLs, Spare Wheel protector.
1996 300Tdi - Eaten by tin worms
7th Jul 2022 1:21 pm
KevinD3
Member Since: 05 Aug 2020
Location: Sutton Coldfield
Posts: 1250
Hi Moleshome, it’s a slightly smaller diameter than a standard 12v replacement like the below. They’re a right pain to get out, but if you’re happy to basically destroy the socket a good screwdriver down the side and some will do it.
I replaced mine a duel usb with voltage display (Top left of picture)
My Wife thinks the D3 is a hobby, The D3 thinks the wife is 💕
7th Jul 2022 6:00 pm
Moleshome
Member Since: 15 Oct 2020
Location: Wokingham
Posts: 412
So did you have to enlarge the hole to get the socket that you linked in?
7th Jul 2022 8:47 pm
KevinD3
Member Since: 05 Aug 2020
Location: Sutton Coldfield
Posts: 1250
Their both close to 25mm, I think I ended up just using a sharp knife to clean the edges a bit to fit the new one. I just popped the garage and found one I’ve taken out and a new one (parts hoarder)
It’s he black plastic part of the old one that fits to the hole.
2008 HSE Stornoway Grey
My Wife thinks the D3 is a hobby, The D3 thinks the wife is 💕
7th Jul 2022 8:58 pm
Andy Foster
Member Since: 27 Dec 2009
Location: Liverpool
Posts: 6551
Not sure on the diameter but to fit an aftermarket outlet you’d need to get the trim off or at least pull the top back to get your hands in to fit the new outlet. The panel is all one piece and is a bit of a pain to get out though.
D4 MY15 SE TECH
D3 gone but never forgotten.
7th Jul 2022 9:20 pm
Moleshome
Member Since: 15 Oct 2020
Location: Wokingham
Posts: 412
Thank you both, looking at the Ebay link that says 2.87cm so it sounds as though the hole is slightly less than that.
Andy, does that top bit with the storage bin pop off?
7th Jul 2022 10:07 pm
pwheeldon
Member Since: 15 Jan 2020
Location: West Yorks
Posts: 1462
It does come off, but you need to take off the c and d pillar trim ideally.
I fitted an SAE socket on the other side and just drilled it as I was pretty sure nothing was there. If you need to open up the hole a cone cutter is ideal.Discovery 4 GS 2009 Auto Stornoway Grey
Discovery 3 s 2005 Auto Bonatti Grey Gone
Discovery 3 SE 2005 Manual Zambezi Silver Gone
Range Rover Sport HSE 2006 Black
Aston Martin DB7 VV
8th Jul 2022 1:48 pm
Andy Foster
Member Since: 27 Dec 2009
Location: Liverpool
Posts: 6551
Moleshome wrote:
Thank you both, looking at the Ebay link that says 2.87cm so it sounds as though the hole is slightly less than that.
Andy, does that top bit with the storage bin pop off?
It does come off but doesn’t just pop off. I still think you would need to take the whole panel off to do it. From memory, and I’ve been drinking , I think it’s held on with clips but I still think you’d need to take the panel off to separate the two pieces.D4 MY15 SE TECH
D3 gone but never forgotten.
8th Jul 2022 8:57 pm
qcnr
Member Since: 23 Nov 2017
Location: Norway
Posts: 117
Depends how much access you need. I'm doing this at the moment and to get enough access to wiring
and sockets etc, remove the tailgate wire, pop off the rubber boot seal, then remove the rear boot flap. Lift up the floor for the tool kit and then undo the floor panel at the side, mine had load hooks so undid those and it pulled up with a bit of oomph. Now you can pop off the 3 plastic studs holding on the panel and you can pull it out of the way. Gives good enough access for small jobs.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum