Member Since: 23 Sep 2019
Location: Richmond
Posts: 118
Engine seized solid in either direction, turn flexplate ?
I am trying to remove the engine from gearbox, to remedy the broken crankshaft.
The engine will not move in either direction, it is even possible to undo the very tight crank pulley bolt.
What is the easiest method for moving/turning the flexplate in order to undo the bolts?
11th Dec 2021 8:03 am
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
Normally you can turn them a few degrees in one direction from the front that then allows you to turn the flexi plate by a few degrees. Its a pain but you can usually get them to turn enough to get all four bolts out by working it back and forawrd.
It not you will have to pull the torque converter out with the engine but a lot of oil will come out.Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
11th Dec 2021 9:00 am
johnhorgan
Member Since: 23 Sep 2019
Location: Richmond
Posts: 118
Thats all I could think of, just taking it out with the converter attached.
I have drained the gearbox oil, can you think of any other tactics ?
11th Dec 2021 9:04 am
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
Have you taken the body off? You need to lift the engine and gearbox up quite high to get the sump to clear the front axle if your removing the TC with the engine.
Normally the engine slides forward until it touches the axle and then lifts up but with the extra length of the TC it wont come far enough forward to clear the gearbox, i dont know if removing the sump makes a difference if you still have the body on.Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
11th Dec 2021 9:12 am
johnhorgan
Member Since: 23 Sep 2019
Location: Richmond
Posts: 118
I have taken the body off.
Do you think it will clear the front axle ok provided I raise the engine/gearbox enough?
11th Dec 2021 9:48 am
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
Yes it does i have done it a couple of times, you have to disconnect the front propshaft to allow the gearbox to come up enough and you have to support the gearbox so it doesnt drop down once it clears the engine.
If you are able it would almost be easier to remove the engine and gearbox together, i have not done it this way but there are only a few extra things to remove to make it possible.Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
11th Dec 2021 10:15 am
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
11th Dec 2021 10:16 am
johnhorgan
Member Since: 23 Sep 2019
Location: Richmond
Posts: 118
Thanks for the help, I will let you know how I go.
11th Dec 2021 6:56 pm
johnhorgan
Member Since: 23 Sep 2019
Location: Richmond
Posts: 118
Well it all came apart ok!
Now I have to get the torque converter off.
Undo the sump and loosen the crankshaft looks like the best option.
12th Dec 2021 12:53 am
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
Yes i think its your only option its going to come off anyway.Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
12th Dec 2021 8:56 am
johnhorgan
Member Since: 23 Sep 2019
Location: Richmond
Posts: 118
Crankshaft snapped and wedged.
Click image to enlarge
14th Dec 2021 8:29 am
johnhorgan
Member Since: 23 Sep 2019
Location: Richmond
Posts: 118
Finally after lots of hammering with a 4lb hammer, its out !
Click image to enlarge
14th Dec 2021 8:36 am
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
I bet the block is out of true with the crank wedged like thatAndrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
14th Dec 2021 4:28 pm
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4471
Ooo, that's nasty. Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
14th Dec 2021 4:35 pm
johnhorgan
Member Since: 23 Sep 2019
Location: Richmond
Posts: 118
Yes I think the block is scrap.
I am going to see if I can fit the heads on a 2.7 block, can anyone think of any problems?
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum