P_MK5
Member Since: 21 Apr 2016
Location: Kent
Posts: 26
  
|
Just installed a BritPart FBH Controller to Disco 3. All went well, remote flashes green every 15 sec.
But when trying to operate pushing LR button on remote once lights come on, wait 4-5 sec then push again it does not start the FBH. Car is cold and temp is below 4Deg.
The FBH was working the morning I installed, smoke was coming out of LH wheel exhaust.
Any help or fixes would be welcome.
Regards
Paul.
|
 4th Dec 2016 3:20 pm |
|
|
Bodsy
Site Sponsor
Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361
 
|
Do you get any flashing from the led on the controller when you activate it? Any noise of fans in the FBH at all? Bodsys Brake Bible
D4/D3 Remote FBH heat kits
BAS Remaps/ EGR Blank
Transmission Flush
Software updates/enabling
Clock/ SNOTM /3Flash / 4x4Info /BT Update /Service Reset/Error Codes / Gearbox Reset
See It Here
|
| 4th Dec 2016 3:31 pm |
|
|
Narpy
Member Since: 18 Jul 2011
Location: Stockport
Posts: 7830
|
Brit Part are selling FBH controllers?
Didn't know that. Mods:
Front Fogs + Halos
FBH Remote Control
The 1st Ever RRS Modded Grill
Garmin Nuvi + D4 Surround + Reversing Camera.
D4 Steering Wheel.
Rear Boot Spoiler.
Twin Brake Lights.
Wing Mirror Indicator Repeaters.
Long Roof Rails
Make your own Narpy grill thread
I'm not scared, I'm outta here.
|
| 4th Dec 2016 3:32 pm |
|
|
Bodsy
Site Sponsor
Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361
|
They've been selling the BAS controllers for a while. Bodsys Brake Bible
D4/D3 Remote FBH heat kits
BAS Remaps/ EGR Blank
Transmission Flush
Software updates/enabling
Clock/ SNOTM /3Flash / 4x4Info /BT Update /Service Reset/Error Codes / Gearbox Reset
See It Here
|
| 4th Dec 2016 3:38 pm |
|
|
M3DPO
Member Since: 22 Sep 2010
Location: Notts.
Posts: 8238
 
|
It won't start if the low fuel light is on.  It can when others can't,
It will when others won't,
It goes where others don't.
|
| 4th Dec 2016 3:38 pm |
|
|
|
|
P_MK5
Member Since: 21 Apr 2016
Location: Kent
Posts: 26
|
Got full tank of fuel, and it is under 4 degrees
|
| 4th Dec 2016 3:46 pm |
|
|
eightfoot
Member Since: 12 Apr 2015
Location: sunny essex
Posts: 808
|
when you press to start count to 3 whilst holding then realease,my bas plip seems to work better that way,if you are using the 3rd button on the remote (lr) you need to set it to flash lights (coming home see handbook) function,also works by supplying power for 3 secs to the wire you connect to the headlights
just reread is your battery fully charged it wont start the heater if below 12.2 volts please excuse any grammer/punctuation mistakes,i'm thick,thankyou
current vehicles 2005 d3 2013 d4
|
| 4th Dec 2016 4:00 pm |
|
|
P_MK5
Member Since: 21 Apr 2016
Location: Kent
Posts: 26
|
Using 3rd button on key fob, it is set for follow me home lights, battery is 12.5 volts stopped and 14v when engine running.
|
| 4th Dec 2016 4:08 pm |
|
|
Bodsy
Site Sponsor
Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361
|
P_MK5 wrote:Bodsy
Yes, the green LED light flashes every 15 sec as per installation check sheet. No noise at all.
Narpy
https://www.jgs4x4.co.uk/land-rover-discov...er-da6349/
But what happens when you press the lights on for three or five seconds? Does the LED status change? It should do, even if the FBH is faulting.
You connected the blue wire to pin 11 of the headlights? Bodsys Brake Bible
D4/D3 Remote FBH heat kits
BAS Remaps/ EGR Blank
Transmission Flush
Software updates/enabling
Clock/ SNOTM /3Flash / 4x4Info /BT Update /Service Reset/Error Codes / Gearbox Reset
See It Here
|
| 4th Dec 2016 4:55 pm |
|
|
P_MK5
Member Since: 21 Apr 2016
Location: Kent
Posts: 26
|
Thanks for all the help, turns out the splice connector didn't cut the remote blue wire on Pin 11 of head light. All working good now. 
|
| 5th Dec 2016 6:53 pm |
|
|
Narpy
Member Since: 18 Jul 2011
Location: Stockport
Posts: 7830
|
Only got yourself to blame I'm afraid, those Scotchloks are notorious around the forum for causing exactly what you describe.
Cut and solder every time unless access is a major problem. Mods:
Front Fogs + Halos
FBH Remote Control
The 1st Ever RRS Modded Grill
Garmin Nuvi + D4 Surround + Reversing Camera.
D4 Steering Wheel.
Rear Boot Spoiler.
Twin Brake Lights.
Wing Mirror Indicator Repeaters.
Long Roof Rails
Make your own Narpy grill thread
I'm not scared, I'm outta here.
|
| 5th Dec 2016 7:15 pm |
|
|
P_MK5
Member Since: 21 Apr 2016
Location: Kent
Posts: 26
|
Thanks for the  
That's exactly what I did 2nd time round, trimmed the cable cover back pushed hole through and soldered new blue cable in and then heat shrinked and taped.
|
| 5th Dec 2016 7:43 pm |
|
|
Jackdiscovery3
Member Since: 16 Jun 2021
Location: Uk
Posts: 2
|
Hi guys looking for some help, I have just bought a second hand britpart fbh controller. I have installed in no problem and it works using the 3rd button but I am struggling to connect it to the app as it is asking for a qr code that I don’t have. Also, when I text it I get no response but the previous owner gets a notification when it turns on etc. Any ideas how to fix this?
Thanks in advance
|
| 6th Oct 2021 6:11 am |
|
|
