Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
  Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate · Register · Log In  
DISCO3.CO.UK > IIDTool Help

First Use IID Parking Sensor and Eco Issues
Post Reply  Down to end
Page 1 of 1
Redroof
 


Member Since: 21 Apr 2017
Location: Argyll
Posts: 21

Scotland 2016 Discovery 4 3.0 SDV6 Landmark LE Auto Waitomo GreyDiscovery 4
First Use IID Parking Sensor and Eco Issues

Hi all,
Hoping someone can help here, I used my IID BT tool for the first time this morning after activation/ registration etc.
I was hoping to activate the towing modules (tow electrics fitted by me) as I expect to be towing soon and wanted the parking sensors etc disabled when in reverse with the tow attached. I had tested the 13 pin electrics after I fitted them and all were working.
However, after selecting 13 pin, tow ball attached and tow bar attached on the IID tool the eco start/ stop warning is now on the dashboard and the parking sensors don’t work at all.
Having given myself the fear, I restored everything using the initial back up made when activating the tool.
Even now, the eco start stop warning is active and I have no parking sensors.
I suspect the eco issue is due to a drop in battery voltage from using the IID, but I don’t know about the parking sensors.
Any help would be greatly appreciated.
Cheers
Garry Current Stable
1998 300TDi Defender 90 'Daisy'
2006 Audi RS4 Avant Daytona Grey 'Ava' (just cant let go)
2016 D4 Landmark Waitomo Grey 'Dora'  
Post #21778114th Oct 2020 10:55 am
View user's profile Send private message View poster's gallery Reply with quote
grzesiul
 


Member Since: 11 May 2008
Location: UK
Posts: 6369

Poland 2016 Discovery 4 3.0 SDV6 SE Auto Loire BlueDiscovery 4

Hello,
Have you made changes to the CCF with any good battery charger attached in supply mode to prevent battery drain? I guess S/S system is showing as on due to battery state.
Have you ran fault codes reading? Try setting up the tool to include pending faults and click on show all faults on the tool. Make sure your battery is charged though.
Have you enabled all below as per Gap site?


All except Range Rover L322 2002-2009

– Tow bar -> Yes

– Trailer module -> select the correct one

– Trailer stability assist -> Yes (will only work if surround cameras are fitted)

– Trailer towing ball -> Fitted

Good luck resolving the issue.
Greg  
Post #21778194th Oct 2020 11:32 am
View user's profile Send private message View poster's gallery Reply with quote
Redroof
 


Member Since: 21 Apr 2017
Location: Argyll
Posts: 21

Scotland 2016 Discovery 4 3.0 SDV6 Landmark LE Auto Waitomo GreyDiscovery 4

Hi Greg,
No battery charger connected, my 5A Ctek doesn’t do supply mode but the battery was showing 14.5V in the initial display. It subsequently dropped to 13.1V when I had restored everything to the back up.
All modules initially adjusted as per the Gap site and your post.
Here is a daft question though that I’ve not considered, do the parking sensors work with the EPB on? I did get a parking sensor failure message and a tone but since restoring everything the message nor the tone returned.
I’ve had a cup of tea so I’m ready to return to this!
There is a fault code on the engine module that doesn’t clear, but I can’t remember what it says. I’ll screen shot it next time.
Cheers
Garry Current Stable
1998 300TDi Defender 90 'Daisy'
2006 Audi RS4 Avant Daytona Grey 'Ava' (just cant let go)
2016 D4 Landmark Waitomo Grey 'Dora'  
Post #21778394th Oct 2020 12:12 pm
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10669

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

No park sensors don’t work with park brake on.

Still worth connecting your 5A charger.  
Post #21778434th Oct 2020 12:45 pm
View user's profile Send private message View poster's gallery Reply with quote
Disco_Mikey
 


Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20831

Scotland 2005 Discovery 3 TDV6 HSE Auto Cairns BlueDiscovery 3

Check other modules for codes, and clear them too

D4 seems to struggle at times, for instance, bringing the EML on, despite logging no codes in the engine system, caused by a fault in the TCM

Clear all faults does not actually clear all the faults, and some needs clearing by individual ECU Thumbs Up My D3 Build Thread

TDV8 Retrofit Build Thread  
Post #21778474th Oct 2020 12:53 pm
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
Redroof
 


Member Since: 21 Apr 2017
Location: Argyll
Posts: 21

Scotland 2016 Discovery 4 3.0 SDV6 Landmark LE Auto Waitomo GreyDiscovery 4

So, indeed the parking sensors do not work when the EPB is on, I’ve not noticed this in the 4 years I’ve had the car Embarassed
Also, the eco start/ stop warning was gone when I got back out to her
So the original job is done for the tow electrics but I’ve now got three fault codes as per the attached pic.
Any pointers on the engine code would be appreciated!
Thanks for the assistance so far! Current Stable
1998 300TDi Defender 90 'Daisy'
2006 Audi RS4 Avant Daytona Grey 'Ava' (just cant let go)
2016 D4 Landmark Waitomo Grey 'Dora'  
Post #21778814th Oct 2020 3:14 pm
View user's profile Send private message View poster's gallery Reply with quote
grzesiul
 


Member Since: 11 May 2008
Location: UK
Posts: 6369

Poland 2016 Discovery 4 3.0 SDV6 SE Auto Loire BlueDiscovery 4

Hey
Windshield misting sensor sits in small plastic box behind rear view mirror on driver side on blacke out portion of windshiled
I had same error and it was faulty cost round 20 quid repacement is plug and play
As to U type code it states:
NOTE: Monitor description.
Engine control module has been
informed of a failure within the dual
battery system
Inspect connectors for signs of
water ingress, and pins for
damage and/or corrosion
Refer to the electrical circuit
diagrams and check connections
are secure and wiring integrit

Good luck, and I guess SS battery ()small one) is done ?
Rgds
Greg  
Post #21778854th Oct 2020 3:22 pm
View user's profile Send private message View poster's gallery Reply with quote
Redroof
 


Member Since: 21 Apr 2017
Location: Argyll
Posts: 21

Scotland 2016 Discovery 4 3.0 SDV6 Landmark LE Auto Waitomo GreyDiscovery 4

Got the sensor on order, and hopefully that will solve the other temperature control issues that LR don’t understand.
As for the other U code, I’ll wait until the next service in 2 weeks to see what’s what.
Thanks to all everyone for all the help, can always count on the members here to assist!
Cheers Current Stable
1998 300TDi Defender 90 'Daisy'
2006 Audi RS4 Avant Daytona Grey 'Ava' (just cant let go)
2016 D4 Landmark Waitomo Grey 'Dora'  
Post #21779004th Oct 2020 4:09 pm
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10669

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

Don’t worry about U codes unless somethings not working  
Post #21779224th Oct 2020 5:20 pm
View user's profile Send private message View poster's gallery Reply with quote
Redroof
 


Member Since: 21 Apr 2017
Location: Argyll
Posts: 21

Scotland 2016 Discovery 4 3.0 SDV6 Landmark LE Auto Waitomo GreyDiscovery 4

Everything appears to be working, so not too concerned, good to know though.
It’s a good tool but not quite as nice to use as the VAGCOM for Audi VW group vehicles. Current Stable
1998 300TDi Defender 90 'Daisy'
2006 Audi RS4 Avant Daytona Grey 'Ava' (just cant let go)
2016 D4 Landmark Waitomo Grey 'Dora'  
Post #21779284th Oct 2020 5:33 pm
View user's profile Send private message View poster's gallery Reply with quote
Disco_Mikey
 


Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20831

Scotland 2005 Discovery 3 TDV6 HSE Auto Cairns BlueDiscovery 3

I'm the opposite. I thought VCDS was a nightmare to navigate, and any coding could only be done if you knew the options codes My D3 Build Thread

TDV8 Retrofit Build Thread  
Post #21779334th Oct 2020 6:17 pm
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
Redroof
 


Member Since: 21 Apr 2017
Location: Argyll
Posts: 21

Scotland 2016 Discovery 4 3.0 SDV6 Landmark LE Auto Waitomo GreyDiscovery 4

I think the interface is more user friendly as long as you have the wiki handy with all the codes but I see your point!
I think I’m just more used to VCDS, the flashing of ECUs with the IID puts the sh*tiers right up me! And the instruction manual is pretty daunting for the IID, but using it and understanding the changes is pretty straightforward. Current Stable
1998 300TDi Defender 90 'Daisy'
2006 Audi RS4 Avant Daytona Grey 'Ava' (just cant let go)
2016 D4 Landmark Waitomo Grey 'Dora'  
Post #21790869th Oct 2020 3:29 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
< Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums
DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site