Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
  Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate · Register · Log In  
DISCO3.CO.UK > My Discovery 4

rear prop shaft centre bearing
Post Reply  Down to end
Page 1 of 1
John-in bsly
 


Member Since: 30 Nov 2009
Location: barnsley south yorkshire
Posts: 37

England 2016 Discovery 4 3.0 SDV6 SE Auto Corris GreyDiscovery 4
rear prop shaft centre bearing

Hi all

Does anyone have experience of replacing a rear prop shaft centre bearing?

Had my 2015 motor in for its last service package service and MOT today, advisories where prop shaft joint worn(but not excessively) £728 to replace + both rear tyres nearing legal limit goodyear wranglers 19" at £217 each Rolling with laughter have already found them for £145 each fitted without much effort.

I've seen some centre bearings on the market for £25/£30

Any information appreciated

Thanks
John I'm not arguing, I'm simply explaining why I'm right!

1994 300 tdi in Niagra grey
2006 D3 in Zambezi silver
2015 D4 in Corris grey
2024 defender 110 xs silicon silver has some big boots to fill
Planet X 29 Lurcher in black
Planet X Lynskey titanium Sportive in.... titanium  
Post #21581081st Jul 2020 9:58 pm
View user's profile Send private message View poster's gallery Reply with quote
TigerRecovery
 


Member Since: 31 May 2017
Location: Long Stratton, Norwich, Norfolk
Posts: 901

Wales 2016 Discovery 4 3.0 SDV6 Landmark LE Auto Waitomo GreyDiscovery 4

Only replace the whole propshaft with a GKN part, if you just replace the bearing to get it through an MoT you'll pay again within 2 years to replace it with another one.

The only company that will replace it properly is GKN who make the propshafts.

You've got to take the propshaft off to replace it anyway and it's quicker just to put a new one back on. You can even do it yourself on the driveway but make sure the vehicle is chocked up. 1972 Range Rover Classic 2 door V8
2013 Land Rover Discovery 4 HSE - SCRAPPED
2016 Land Rover Discovery 4 Landmark
2022 Volvo XC40 T5 PHEV 282HP FWD 3 cylinder!  
Post #21581111st Jul 2020 10:12 pm
View user's profile Send private message View poster's gallery Reply with quote
darrind
 


Member Since: 04 Jul 2008
Location: In A World of My Own!
Posts: 2908

England 2013 Discovery 4 3.0 SDV6 HSE Auto Santorini BlackDiscovery 4

I bought a GKN one and a set of bolts from Rimmers and swapped mine in the drive in around 1 hour for around 1/3 of what you have been quoted (need some decent sockets axle stands or a pair of ramps and a torque wrench) there are lots of people who have used Sikaflex to repair the centre rubber bearing on the shaft but tbh I would just change it as you replace all the joints then in one hit. Even if you pay an Indi to do the job you will save a fortune Thumbs Up Thumbs Up Must stop buying shiny toys....  
Post #21581121st Jul 2020 10:12 pm
View user's profile Send private message View poster's gallery Reply with quote
Gary_P
 


Member Since: 03 May 2016
Location: Kent
Posts: 1679

Ukraine 2016 Discovery 4 3.0 SDV6 HSE Auto Corris GreyDiscovery 4

Part is around £250 and it will take a good independent an hour to fit. Just had mine done under warranty (WD). Was quoted £650 from LR dealer.
All the research points to doing the whole thing and using GKN.
Cheers Gary
-------------------------------------------

Discovery 4 HSE 2016MY  
Post #21581342nd Jul 2020 6:48 am
View user's profile Send private message View poster's gallery Reply with quote
JackNorris
 


Member Since: 06 Jul 2012
Location: Beds/Bucks Border
Posts: 1879

United Kingdom 2005 Discovery 3 4.4 V8 HSE Auto Tonga GreenDiscovery 3

Do it yourself, took us around 45 minutes on the drive. Just ensure vehicle is chocked. MY2023 Discovery 5 R-Dynamic 3.0
MY2020 Discovery 5 Landmark 3.0 - SOLD
MY2005 Discovery 3 V8 4.4 HSE - SOLD
MY2019 Discovery 5 SE 3.0 - LR Replaced !
MY2005 Discovery 3 S 2.7 - SOLD
MY2016 Discovery 4 Graphite - SOLD
MY2015 Discovery 4 SE Tech - SOLD  
Post #21581532nd Jul 2020 8:25 am
View user's profile Send private message View poster's gallery Reply with quote
lynalldiscovery
 


Member Since: 22 Dec 2009
Location: Maidstone
Posts: 7274

United Kingdom 2006 Discovery 3 TDV6 Metropolis LE Auto Bonatti GreyDiscovery 3

If it is the rubber part that has failed as oppossed to the bearing itself, you can of course carry out a time honoured bodge for a tenner.
Youtube repair bushes with pu sealant and see what comes up.

One of many vids,   
Post #21582912nd Jul 2020 7:36 pm
View user's profile Send private message View poster's gallery Reply with quote
John-in bsly
 


Member Since: 30 Nov 2009
Location: barnsley south yorkshire
Posts: 37

England 2016 Discovery 4 3.0 SDV6 SE Auto Corris GreyDiscovery 4

Hi Guys

Thanks for your input, think a new GKN shaft is the way to go,I have an independent garage nearby who works mostly with defenders and earlier disco's so think he will get the job. At 68 I'm past rolling around under motors (but have done plenty of it in the past). The fault is an advisory so no rush to get it done will let you know outcome

Thanks
John I'm not arguing, I'm simply explaining why I'm right!

1994 300 tdi in Niagra grey
2006 D3 in Zambezi silver
2015 D4 in Corris grey
2024 defender 110 xs silicon silver has some big boots to fill
Planet X 29 Lurcher in black
Planet X Lynskey titanium Sportive in.... titanium  
Post #21583122nd Jul 2020 9:06 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
< Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums
DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site