Member Since: 06 May 2015
Location: Bromley
Posts: 331
IIDTOOL help
So received my IIDTOOL BT today (Thanks Dan). However it doesn't seem to want to play nice.
First issue was that it worked for a couple of minutes then couldn't connect stating firmware was out of date. I researched and fixed this updating the firmware to the latest version.
Now I can connect again but as soon as I try to access "Car Config", I get a "Select CCF" screen with a blank box entitled "Confirmed List..." at which point the app just hangs. Have to kill the app in android settings to get out of this. Then I can't reconnect to the tool again afterwards.
Any ideas?
22nd Aug 2018 9:38 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10368
Did you register it with your vin number. ?
That is required for ccf edit
22nd Aug 2018 9:50 pm
webego
Member Since: 06 May 2015
Location: Bromley
Posts: 331
I thought I had (activate via app) but then that was also around the time it complained about firmware version. I'll see if I can check that on the website itself.
22nd Aug 2018 10:08 pm
webego
Member Since: 06 May 2015
Location: Bromley
Posts: 331
Yep, certain it is activated correctly. Also remember the VIN showing up when connecting.
22nd Aug 2018 10:16 pm
webego
Member Since: 06 May 2015
Location: Bromley
Posts: 331
Manged to get a bit more out of the IID but after 5 or so mins it starts flashing green then nothing works. I have to disconnect and totally power off the car and start again.
22nd Aug 2018 11:16 pm
paulf
Member Since: 23 Sep 2017
Location: Rutland
Posts: 91
I’ve had the same (using Apple though) as have others. I find it much better if you turn off Wi-fi on your phone/tablet. I’m sure it’s a software issue.Discovery 4 XXV
BMW 530d M Sport plus
BMW R1200GS Adventure
Aprilia RSV1000 Tuono
22nd Aug 2018 11:20 pm
webego
Member Since: 06 May 2015
Location: Bromley
Posts: 331
Thanks for the info. Not great at £400 a pop if this is a common problem. Without wifi also seemed to work better but didn't stop it hanging though.
I'll have a check of the socket tomorrow to check all the pin connectors are good after reading something in their FAQs.
22nd Aug 2018 11:27 pm
webego
Member Since: 06 May 2015
Location: Bromley
Posts: 331
So managed to get some faults out after several attempts of connecting and clearing all existing faults.
-------------
Model L319 - Discovery 3 2006
Vehicle scanned on 22 Aug 2018 23:11:25
IIDControl 2.9.4.5 Android - IIDTool BT V3.0 B2481
Body Control
B1B02-28 (2F) Low frequency coil - General signal failure - signal bias level is out of range/zero adjustment failure
( on 17-05-2017 01:22:43 at 178810 km )
B1B70-01 (28) Local interconnection network bus circuit 2 - General failure information - general electrical failure
( on 17-05-2017 01:56:17 at 178810 km )
B1C57-14 (6C) Passive start ignition relay coil circuit - General electrical failure - circuit short to ground or open
( on 17-05-2017 01:20:07 at 178810 km )
U0155-87 (28) Lost communication with instrument cluster control module - Bus signal/message failure - missing a message
( on 17-05-2017 01:56:17 at 178810 km )
Cell Phone
B1A00-47 (AF) Control module - System internal failure - watchdog/safety failure
( on 17-05-2017 03:49:29 at 178816 km )
U3000-54 (AF) Control module - System programming failure - missing calibration
( on 17-05-2017 03:49:29 at 178816 km )
Engine TDV6
P0405-00 (2D) Exhaust gas recirculation sensor A - circuit low
Suspension
C1A20-64 (2E) Pressure increases too slow when filling reservoir - Algorithm based failure - signal plausibility failure
( on 17-05-2017 01:22:25 at 178816 km )
Vehicle Dynamic
U0132-87 (08) Lost communication with ride level control module - Bus signal/message failure - missing a message
( on 17-05-2017 01:46:47 at 178816 km )
-------------
Body Control
Done some research on these codes and apparently I can ignore all of these. Shout if you think differently.
Cell Phone
I suppose this is because I bought the car with an old phone connector in the arm rest compartment which I took off. Would like to remove this completely if possible if anyone knows how?
Engine
I guess I can ignore that scary looking engine fault (P0405-00) as I have the EGR blanked?
Suspension / Vehicle Dynamic
I'll hopefully have the suspension fault fixed tomorrow when I fit the new (second) amk compressor (already replaced the reservoir tank, reservoir valve block and front valve block). Maybe the Vehicle Dynamic fault is a cascade from the Suspension?
C1A20-64 (2E) Pressure increases too slow when filling reservoir - Algorithm based failure - signal plausibility failure
( on 17-05-2017 01:22:25 at 178816 km )
This is the only one that needs looking at.
Flack
23rd Aug 2018 8:57 am
webego
Member Since: 06 May 2015
Location: Bromley
Posts: 331
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum