Member Since: 28 May 2014
Location: Cheshire
Posts: 189
Door lock button on the drivers side is sorted by using a none memory seat switch pack, it then looks like the passenger side? J
24th Sep 2016 1:33 pm
dennyrol
Member Since: 27 Jul 2015
Location: Moscow
Posts: 58
Yes, I'm on both sides of the lock buttons of the doors.
24th Sep 2016 2:49 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
Are you saying you got the drivers window switch working by using a D4 wiring loom and a D4 window motor? All 4 window buttons work on the D3? Does the D4 window motor fit the D3?
24th Sep 2016 5:40 pm
dennyrol
Member Since: 27 Jul 2015
Location: Moscow
Posts: 58
Experimenting my friend. Any 3 doors. The driver door is faulty a long time, so long as it is the buttons don't work. In the rest of the doors works. My friend put the window motor in the D3. But I need the wiring from the D4, it's difficult to connect. Still need to pull from driver door to passenger-carrying wire, what would they, too, were the total signal. If You can find the electrical diagram of the D4, You will understand what I mean. Please make sure that you have blocks of comfort on the door cards, especially the driving was serviceable.
The experiments continue)))
24th Sep 2016 5:57 pm
Ginner
Member Since: 28 May 2014
Location: Cheshire
Posts: 189
There is another similar thread running on this, I used a D3 inner switch plastic welded into the D 4 switch surround. Everything works.......J
24th Sep 2016 10:52 pm
Ginner
Member Since: 28 May 2014
Location: Cheshire
Posts: 189
There is another similar thread running on this, I used a D3 inner switch plastic welded into the D 4 switch surround. Everything works.......J
24th Sep 2016 11:05 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
Any pics ginner?
24th Sep 2016 11:30 pm
Ginner
Member Since: 28 May 2014
Location: Cheshire
Posts: 189
Pm me your email address and I'll send some over to you.... J
25th Sep 2016 2:53 pm
Ginner
Member Since: 28 May 2014
Location: Cheshire
Posts: 189
Pm me your email address and I'll send some over to you.... J
25th Sep 2016 2:53 pm
dennyrol
Member Since: 27 Jul 2015
Location: Moscow
Posts: 58
Irwin Good day! Help, can't figure which wire on the connector is responsible for what. Are you calling the Pin on the lock buttons on the middle console, and door card, which Pin is needed? Try to connect one by one, no lights nothing..(((
Click image to enlarge
25th Sep 2016 8:01 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
Pin 1,2,5 on the door are used for locking leaving pins 3&4 for light.
Pin 4,10,15 on the console
Pin 1-pin4
Pin 2-pin10
Pin 5-pin15
25th Sep 2016 8:33 pm
dennyrol
Member Since: 27 Jul 2015
Location: Moscow
Posts: 58
Connect the battery to the 3 and 4 Pin, but there is no light(( 3 and 4 Pin is the plus and minus? In the previous answer, You mean Pin 3 did not write anything.. If the black wire (ground) is Pin 5, Pin 4 is the red wire (plus), the 3 Pin is which wire and why? Help
25th Sep 2016 9:05 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
I dont know dennyrol. I have only wired up 3 wires to get them to lock/unlock. I have a D4 loom and it has 5 wires to the door handle. Pins 1-5. The wiring diagram i have only lists 3 wires.
25th Sep 2016 9:32 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
I just went out to have a look and pins 3&4 must connect together to plus and pin 5 is minus.
25th Sep 2016 9:43 pm
Irwin
Member Since: 04 Aug 2015
Location: Internet
Posts: 270
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
