I know wheels and body panels have been done but has anyone tried doing the exterior door handles? If so how have they held up? I think I'm going to do all my letters and was thinking of turning the handles black too to match.
Skep'16 Volvo XC90 R Design Bursting Blue (Vera)
'12 Discovery 4 3.0 SDV6 HSE Fuji White (Daz - Gone
'10 Discovery 4 3.0 TDV6 HSE Santorini Black (Vinnie - Gone)
'07 Discovery 3 2.7 TDV6 SE Stornoway Grey (Gone)
Club Side Skeps
12th May 2014 2:45 pm
euangibson
Member Since: 24 Dec 2010
Location: Borders
Posts: 11027
I have considered this too.
The answer I got about how easy it was to remove it from wheels made me think again....a decent bit of elbow grease is all that's needed to remove it....I decided the heavy traffic a door handle gets would mean I'd be forever re-applying it.....
If someone has done it,and it lasted,I'd reconsider "Better to remain silent and be thought a fool,than to speak out and remove all doubt" ?.....what rubbish...
Locking rear E-diff
RLD spare wheel protector & sump guard
Extended roof rails
Series 111 mudflaps
Black side tubes,grill and vents
Timed climate remote
Hids4u interior lights
D4 Firenze my2012 HSE
D3 Java 2005 SE manual (sold,sadly,thanks for the memories)
1966 '88 Series 2a....still starts in the morning better than I do...
12th May 2014 3:10 pm
Scarab
Member Since: 11 Jun 2011
Location: Hastings
Posts: 1283
I had this on a previous car and will be doing it on the D3 within the next couple of weeks.
Plastidip holds up just fine if you apply it carefully enough and with enough coats.
Keep in mind that Plastidip was primarily designed to be used to applying to tools as a non-slip material for the handle so it does stand up to a good amount of pull/twist treatment.
Member Since: 12 Mar 2014
Location: coventry
Posts: 1
Hi Skep, How are you planning on doing the letters, will you leave them on or will you have to remove then refit?
Thanks
Richard
19th May 2014 7:39 pm
nighthawk
Member Since: 24 Jul 2010
Location: Malta
Posts: 1163
Definitely leave them on.
I did mine. Simply mask off the area ... leave at least 1 inch around the letters to give you something to peel off. Plastidip the entire rectangle. Then just before it dries completely you peel off the excess... it comes away quite nicely if you apply nice thick coatings. All you will have left then is to pick at (using a toothpick or tweezers) and peel the excess from inside the "closed" letters..ie. the A, D, R, O and 6.
Very easy to do
There are a few videos on youtube showing how to plastidip emblems etc if you want to watch how it's done.Dennis
2006 Discovery 3 TDV6 Commercial Manual Buckingham Blue
Did mine last weekend, really easy to do, I just got a bit eager and first applied too much in one go so it ran then tried to remove this run and messed a couple of letters up. But just pulled it off and started again, there is still one letter that I'm not completely happy with but will mask it up and do it again at some point. Busy for the next couple of days but planning on doing the handles before the weekend so will take some pictures.
Skep'16 Volvo XC90 R Design Bursting Blue (Vera)
'12 Discovery 4 3.0 SDV6 HSE Fuji White (Daz - Gone
'10 Discovery 4 3.0 TDV6 HSE Santorini Black (Vinnie - Gone)
'07 Discovery 3 2.7 TDV6 SE Stornoway Grey (Gone)
Club Side Skeps
Cheers Amossis, Go down your local DIY store and get some disposable dust sheets, that's all I used then cut some holes in them where the badges were and masking taped around them using the blue low tack tape.
Marcus, the can states 20 mins between coats, I did it when it was warm last weekend and only needed 5 mins between coats then left it about 15 mins (just time for a coffee) and peeled it straight off. I had to redo my 'L' and here is what peeled off. The rest though needs about 4 hours to fully harden.
Honestly you can't really go wrong, worst case you peel it all off and you have back what you had before.
Skep'16 Volvo XC90 R Design Bursting Blue (Vera)
'12 Discovery 4 3.0 SDV6 HSE Fuji White (Daz - Gone
'10 Discovery 4 3.0 TDV6 HSE Santorini Black (Vinnie - Gone)
'07 Discovery 3 2.7 TDV6 SE Stornoway Grey (Gone)
Club Side Skeps
20th May 2014 4:35 am
Russell
Member Since: 23 Aug 2007
Location: Kent
Posts: 10564
So did you mask the letters off exact including the middle of the O or did you mask off the worst and then trin round the letters with a knife before removing off the excess plastidipMY17 D5 1st Edition Namib Orange
MY15 D4 HSE Kaikoura Stone
MY12 D4 HSE Nara Bronze Sold and gone
MY11 D4 HSE Stornaway Grey Sold and gone
D3 S spec Silver Sold and gone
Tow bar, full length roof bars, side steps, tow bar storage unit, surround camers.
D4 camera club
20th May 2014 4:57 am
Landie71
Member Since: 23 Oct 2012
Location: Worksop, Nottinghamshire
Posts: 1019
Thanks Skep - I'll get a can off eBay then - looks like I can't go wrong (probably shouldn't have said that )
Russell, no literally just mask off in a big rectangle around all the letter a as in the first picture, then it just pulls off, I tried it on the kitchen worktop first!! It comes away at the joints, so anywhere there's a gap it just pulls away, for the middle of the 'O' 'D' etc and to get any that don't pull away properly, use a cocktail stick. It hardens after 4 hours and seems pretty stuck now!
Marcus I'd go to Plastidip.co.uk £11 for black and at least you know it's the right stuff and not spray paint!'16 Volvo XC90 R Design Bursting Blue (Vera)
'12 Discovery 4 3.0 SDV6 HSE Fuji White (Daz - Gone
'10 Discovery 4 3.0 TDV6 HSE Santorini Black (Vinnie - Gone)
'07 Discovery 3 2.7 TDV6 SE Stornoway Grey (Gone)
Club Side Skeps
20th May 2014 7:22 am
Bobs
Member Since: 29 Oct 2013
Location: Manchester
Posts: 2330
looks good .....
As they seem black underneath ......
has anyone tried just sanding the top colour off with the correct finishing paper....
I have often wondered about it .....as the sides wouldn't be noticed
Petty sure it would look good but have no ideas on what papers to use D4 Front upgrade/cut back wings n things 'taking a long time but getting there'.
D4 rear upgrade - Narpys helped with that bit
Flack for problem solving and D4 Bluetooth Install/ D4 Heated Steering wheel with Flappy paddles n BBS enabling kit
Disco Mikeys work - Serviced, EGR blanking and 4x4 software upgrade, 3 flash indicators.
B.A.S - FBHIC. Uncle Rays spare wheel protector. Beanie Silver Black badges.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
)
has anyone tried just sanding the top colour off with the correct finishing paper....
