Member Since: 21 Sep 2015
Location: Bodmin
Posts: 32
Parking Aid problems
Discovery 3 2005 HSE.
My parking aid hasn't worked for some time. When I turn the ignition on, I get a 6 second beep from the back, the light flashes on the parking aid button, and if I press the parking aid button the flashing stops but the whole thing remains inactive.
I can not detect any activity from any of the 8 sensors, although they all seem OK when tested with a multi meter (10kohm between pins 1 & 2). I've tested the wiring from the module location to each sensor with a multi meter, it all checks out OK.
I've also tested the CAN wiring, 62 ohms between pins 7 and 14 into the loom, so both terminating resistors are correct.
I've purchased a brand new parking aid module (£130) which has made no difference, so there was probably nothing wrong with the old module.
The Parking Aid (even the new module) doesn't show up in my GAP IID BT tool, which it should do, under Live Values, which makes me think I'm dealing with a CAN BUS fault. (I also drive a RRS 2006, the Parking Aid does show up on the GAP Tool under Live Values on that vehicle).
The only thing I can think of now is the Junction Box - central, which may have had water damage in the past, although it looks clean and OK. I've only had the car for around 12 months, so I don't know what may have happened in the past.
Is it possible that the Junction Box - central may be messing with the Medium Speed CAN BUS, causing a fault in the parking aid system, but leaving the other items on the Medium Speed network OK?
Maybe someone could be good enough to confirm whether or not the Parking Aid does indeed show up in the GAP Tool on the D3 under Live Values? It may be different to the RRS.
Or does anyone have any ideas where the fault may lie? Thanks.
Last edited by SpikeUK on 27th Aug 2023 2:23 pm. Edited 1 time in total
27th Aug 2023 10:30 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14177
Hi
Found the wiring diagrams for u just in case u haven’t got them
Would indeed ensure there’s voltage from the fuses into the parking aid module ( pin 1 ign live ) to ensure that’s ok first then go from there
Hope that helps
Click image to enlarge
Click image to enlarge
Click image to enlarge
27th Aug 2023 1:29 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14177
Hope this also makes life easier
Click image to enlarge
Click image to enlarge
Click image to enlarge
27th Aug 2023 1:43 pm
SpikeUK
Member Since: 21 Sep 2015
Location: Bodmin
Posts: 32
Thanks for putting all that up gstuart, Positive is good to pin 1.
Last edited by SpikeUK on 27th Aug 2023 6:11 pm. Edited 1 time in total
27th Aug 2023 2:25 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10736
well it's good you have an RRS as you should be able to sort it, as they are very similar.
When you say it doesn't show up in live values, do you mean you get N/A rather than 5m
It's a weird one. The flashing light should have stored a fault code.
Check under the CCF settings to ensure park sensors are set to FITTED. (e.g Rear or both).
27th Aug 2023 2:46 pm
SpikeUK
Member Since: 21 Sep 2015
Location: Bodmin
Posts: 32
Click image to enlarge
Pete K, the parking aid module doesn't show up in the GAP tool at all. I attach a photo of the Live Values screen, Parking Aid should be there between Navigation and Parking Brake. Parking Aid doesn't show up in the CCF settings either. The Medium Speed CAN BUS doesn't seem to be seeing the Parking Aid module at all - and it's a brand new module. Every wire connected to the module has been checked out with a multi meter.
I've had the side panel of the left hand side of the boot off for about 3 months now, trying to get to the bottom of why the parking aid isn't working.
Surely the only thing left is the Junction Box Central, isn't that where the MS CAN BUS is controlled from? Thanks for any suggestions.
29th Aug 2023 9:09 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10736
It should show up in the ccf regardless.
I guess you could disconnect it or pull fuse on your RRS to prove that.
I think a cjb replacement is unlikely to fix it.
Personally if I wanted working REAR sensors I would fit a jaguar 2001 xj8 park module.
Almost plug and play. A pin needs connecting to reverse lights. C0957 pin 6 to reverse light wire (green/brown?)
No diagnostics with it, so you would need confidence the sensors were ok or how to fix if they aren’t.
Last edited by Pete K on 31st Aug 2023 11:26 am. Edited 1 time in total
30th Aug 2023 11:44 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10736
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
