| Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate ·
Log In
|
- You are currently viewing DISCO3.CO.UK as a guest - Register to take part or Log In
evo smith
Member Since: 20 Mar 2010
Location: jersey, channel islands
Posts: 16
 
|
| P0501-81 vehicle speed sensor A range/performance |
|
My D4 will move forward and backward but as soon as you give it a little bit of throttle in either drive or reverse, it kicks out of gear and you can hear the transmission spinning. It’s as if the gearbox is confused about what it should be doing.
It all started after i pulled out of junction in normal driving mode.
Not sure if it also feels like its grabbing the brakes as well.
Fault code reader pulls up P0501-81 vehicle speed sensor A range/performance.
Any advice or guidance is much appreciated.
|
 5th Dec 2023 6:59 pm |
|
|
evo smith
Member Since: 20 Mar 2010
Location: jersey, channel islands
Posts: 16
|
Anybody have a possible idea what the problem could be?
|
| 8th Dec 2023 7:54 pm |
|
|
eightfoot
Member Since: 12 Apr 2015
Location: sunny essex
Posts: 810
  
|
six or eight speed ? please excuse any grammer/punctuation mistakes,i'm thick,thankyou
current vehicles 2005 d3 2013 d4
|
| 9th Dec 2023 10:17 am |
|
|
evo smith
Member Since: 20 Mar 2010
Location: jersey, channel islands
Posts: 16
|
Six speed
D4 2010
TDV6 HSE
80k miles.
I have had a very costly few months with it.
I'm praying it's reasonable fix for once 
|
| 9th Dec 2023 3:47 pm |
|
|
eightfoot
Member Since: 12 Apr 2015
Location: sunny essex
Posts: 810
|
first place to look would be the gear selector linkage on the side of the gearbox get someone to go through the selections whilst watching the cable underneath ,the cable should rotate on the link rod as it goes through its curve sweep selecting the gears not bending the selector cable as you check it please excuse any grammer/punctuation mistakes,i'm thick,thankyou
current vehicles 2005 d3 2013 d4
|
| 9th Dec 2023 5:37 pm |
|
|
evo smith
Member Since: 20 Mar 2010
Location: jersey, channel islands
Posts: 16
|
Thanks for the advice, I will get on it in the morning.
|
| 9th Dec 2023 6:15 pm |
|
|
evo smith
Member Since: 20 Mar 2010
Location: jersey, channel islands
Posts: 16
|
The alignment of the cable/rod looks fine.
I have taken apart my original gearbox pivot level arm set up.
Cleaned and greased everything up so that it works nice and smoothly.
I have also ordered a new gearbox lever pivot kit regardless (just waiting for it to arrive).
However, I still have my original problem with the gearbox that I posted.
|
| 16th Dec 2023 1:17 pm |
|
|
eightfoot
Member Since: 12 Apr 2015
Location: sunny essex
Posts: 810
|
have you tried it in low range ? please excuse any grammer/punctuation mistakes,i'm thick,thankyou
current vehicles 2005 d3 2013 d4
|
| 16th Dec 2023 2:56 pm |
|
|
evo smith
Member Since: 20 Mar 2010
Location: jersey, channel islands
Posts: 16
|
Just tried it in low range and it's exactly the same.
|
| 16th Dec 2023 4:03 pm |
|
|
evo smith
Member Since: 20 Mar 2010
Location: jersey, channel islands
Posts: 16
|
I think I have found the problem, the nearside, outer CV joint has gone.
|
| 16th Dec 2023 5:07 pm |
|
|
|
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
|
|
DISCO3.CO.UK is independent and not affiliated to Land Rover.
