Member Since: 06 Mar 2017
Location: Lost
Posts: 4626
Hi Gary,
Is it my eyes or is that the wrong adaptor on the schrader?yµ (idµ - eAµ) ψ=mψ
24th Jun 2021 1:40 pm
lronly
Member Since: 01 Nov 2013
Location: Mellieha
Posts: 66
profsrg i run a full time independent LR garage so its not a one time issue so buying an expensive tool is ok for me........... just as long as it works.
The gauge i have is from FESTO and the pipe with valve from SPX cost me over €200
i have consulted Robbie's bible more than once and i also spoke to him on PM.... this was more than a year ago........... as i said i have been trying with this car for nearly 2 years.... and 2 more independent garages tried and LR local dealer too.....
i have fixed loads of cars with P0087 and P2290 and never had any issues but this one is not a normal car...... it has been to some mechanic that messed it up completely i am facing the consequences.....
i will try changing the entire fuel tank soon
You will find differnet post on different threads form me about this car........ never got anywhere.
24th Jun 2021 1:49 pm
lronly
Member Since: 01 Nov 2013
Location: Mellieha
Posts: 66
i will try with a pipe without adaptor and take off the schrader valve
24th Jun 2021 1:50 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4626
Loose the banjo and fit a straight schrader union. yµ (idµ - eAµ) ψ=mψ
24th Jun 2021 2:07 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13598
PROFSR G wrote:
Hi Gary,
Is it my eyes or is that the wrong adaptor on the schrader?
Must admit haven’t seen one like that before , looks like an oil banjo
24th Jun 2021 2:29 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13598
lronly wrote:
i will try with a pipe without adaptor and take off the schrader valve
Plus 1 , indeed remove it and fit a straight schrader union
Maybe the insert is stuck or full of junk, know I had to replace my Schroeder valve insert
Just remembered after I removed the schrader valve insert , I pushed a rubber tube on and into a container , started the engine allowing any junk to come out , engine off, left the tube on and pushed on the pressure gauge , restarted the engine , worked a treat
Hope all goes well
24th Jun 2021 2:44 pm
lronly
Member Since: 01 Nov 2013
Location: Mellieha
Posts: 66
its a proper schreder valve connection with cock that opens the valve like the ones used to fill gas shocks and the same idea as filling AC gas.... but i will try without it .......... worth the try as i'm more that desperate
24th Jun 2021 3:20 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13598
Please let us know how u get on
Plus Also if u don’t mind me adding , are the seals gone on the throttle body where the large Y fitting is please , as it looks very oily around that area, plus if the Map sensor is clean , not sure if that’s the fuel temperature sensor next to it and if that dirty as well
out of curiosity would u mind taking a closer pic of that valve please or maybe a link, yeh i know I need to get out more, lol , thks
Apologises I’m waffling as per usual
Click image to enlarge
24th Jun 2021 3:30 pm
lronly
Member Since: 01 Nov 2013
Location: Mellieha
Posts: 66
hi all
i have been trying out this car and it seems that it does not do this fault when engine is cold..... it happens when the engine reaches normal running temp.
can anyone indicate to me the max allowable temp of the fuel at which the engine runs normally as i think this could be a cause
thanks
1st Jul 2021 8:49 am
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4626
It depends on various temperature factors, as a guide though a fully warmed up engine (78°c) should show the fuel rail temp at about 60°c. If the fuel temp exceeds 85°c fuel to the injectors will be reduced as will performance until the fuel has sufficiently cooled again. From cold, the fuel temp should be at or very near the ambient temp.
The sensor is part of the fuel spill pipe! yµ (idµ - eAµ) ψ=mψ
1st Jul 2021 2:30 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13598
Hi
Did u check out the throttle body large O rings , as that fuel temperature sensor also looks dirty next to the throttle body Y and Map sensor , alas I might be barking up the wrong tree
How did u get on with the fuel pressure gauge plse
Of course though Prof g is considerably more knowledgeable than myself , it was just something I saw in the picture and if it may have a bearing on the issue
Hope u get it sorted
1st Jul 2021 3:38 pm
lronly
Member Since: 01 Nov 2013
Location: Mellieha
Posts: 66
the fuel temp sensor including fuel return assy is brand new genuine lr since the as i just changed it
2nd Jul 2021 3:14 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13598
Cheers , great that’s done , that’s the one right by the gauge in ur pic isn’t it
Just seeing what looks like oil on that throttle body I wondered if the large O rings were perished
How did u get on with the pressure gauge plse, did u mange to get a measurement in the end , thks
2nd Jul 2021 4:28 pm
lronly
Member Since: 01 Nov 2013
Location: Mellieha
Posts: 66
no ...... it looks like oil but in fact i dropped fuel
6th Jul 2021 6:52 am
Torgeir
Member Since: 14 Apr 2021
Location: Trondheim
Posts: 29
OP back with an update LPFP changed. NO FIX
OP back with an update. I see the thread has been busy while I have been gone. Which is good because I have similar issue to Ironly. That is not promising since he has been at it for 2 years.
Update: Changed the LPFP this weekend and I still get limp mode. Main fault code isP2290‐00 Injector control pressure too low. Today I also got a new code P0089‐22 Fuel pressure regulator performance -general signal failure ‐ signal amplitude maximum.
The car now has a new HPFP and LPFP.
The current draw and pressures from the LPFP got much better after the swap.
5.08 Amp
5 PSI on idle
7.5 PSI not running.
I have been googling and checking around on the forum and some seem to think that P2290 can be caused by the car going into limpmode for another reason. Can anyone confirm this?
Another suggested it was because of faulty height sensors since the car lowered in limp mode. Which mine does. Can anyone confirm i their car lowers or not with regular fuel related limp mode?
One guy had similar issues that disappeared after changing torque converter TC??
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
