Member Since: 05 May 2016
Location: Gateshead
Posts: 473
Help C-1A53-68(eb)
Got this fault code up
Eb latching failure, code c-1a53-68(eb) emergency release activated,
Following some work on the hub rear brakes got this fault help please on how to repair
The disco needs new discs and pads so hoping to sort this out before next week
Cheers once again All transmission oil replaced
3 flash indicators
All timing belts changed
EPB serviced
De cat fitted
Wind deflectors
De-tango done
Tints fitted
Egr blanked
24th May 2018 8:13 pm
XDAndy
Member Since: 16 Jan 2018
Location: Gibraltar
Posts: 597
and consider having a look at the workshop manual. May give a hand with the getting the extended info on this.
24th May 2018 8:52 pm
Henda
Member Since: 05 May 2016
Location: Gateshead
Posts: 473
Will try that tomorrow
Cheers
If all else fails I will fit new discs and arrange a night out in Dundee and try to get DM to sort it
Then enjoy some Scottish hospitality
All transmission oil replaced
3 flash indicators
All timing belts changed
EPB serviced
De cat fitted
Wind deflectors
De-tango done
Tints fitted
Egr blanked
24th May 2018 9:08 pm
Henda
Member Since: 05 May 2016
Location: Gateshead
Posts: 473
Had a look today
ebr is free and easy to pull
IID tool is saying position undefined
On the dash I am getting a red flashing ehb fault light with a dash warning handbrake not applied pull switch
Any ideas anyone
Cheers All transmission oil replaced
3 flash indicators
All timing belts changed
EPB serviced
De cat fitted
Wind deflectors
De-tango done
Tints fitted
Egr blanked
25th May 2018 12:14 pm
Henda
Member Since: 05 May 2016
Location: Gateshead
Posts: 473
Any ideas anyone
Does this point to handbrake switch
Cheers All transmission oil replaced
3 flash indicators
All timing belts changed
EPB serviced
De cat fitted
Wind deflectors
De-tango done
Tints fitted
Egr blanked
25th May 2018 7:05 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4655
Hi Henda,
What work did you have done to the rear brakes?
25th May 2018 7:22 pm
Henda
Member Since: 05 May 2016
Location: Gateshead
Posts: 473
Put a new hub on so had to release the handbrake and it was seized solid had to chop into backing plate to release it , followed the rebuild procedures tightened the disc , 8 clicks back ,pulled the switch got the wurring noise for a few seconds then flashing h/b fault . Now got nothing no noise no h/b ild tool saying it's undefined need to fit new discs next week so I am wondering if it might play again when I fit them
CheersAll transmission oil replaced
3 flash indicators
All timing belts changed
EPB serviced
De cat fitted
Wind deflectors
De-tango done
Tints fitted
Egr blanked
25th May 2018 7:35 pm
Henda
Member Since: 05 May 2016
Location: Gateshead
Posts: 473
O and a dashboard message saying handbrake not applied pull switch
All transmission oil replaced
3 flash indicators
All timing belts changed
EPB serviced
De cat fitted
Wind deflectors
De-tango done
Tints fitted
Egr blanked
25th May 2018 7:37 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4655
Ok perhaps if you could answer these few questions I might get a clearer pic of exactly where you're at!
1. when you say you fitted a new rear hub are you referring to the bearing and knuckle carrier?
2. Does either of the rear wheels rotate, or are they jammed?
3. If they do rotate, can you gear anything abnormal?
4. You say you had to chop into the backplate to release the handbrake, where exactly did you cut? where the HB cable enters the backplate, or somewhere else?
25th May 2018 8:09 pm
Henda
Member Since: 05 May 2016
Location: Gateshead
Posts: 473
Chopped in where the cable enters the back plate wheels turn normally. It's looking like the emergency realise has activated and will not relatch so I think I will fit the new discs next week adjust everything as it should be then try to follow dm post on the Manuel release of the EPB module
In all fairness the rear discs are well shot
But I no longer have an overheating rear n/s hub
Yea All transmission oil replaced
3 flash indicators
All timing belts changed
EPB serviced
De cat fitted
Wind deflectors
De-tango done
Tints fitted
Egr blanked
25th May 2018 8:43 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4655
Is the outer HB cable still able to hold its position behind the backplate, or has it shifted into the hub due to a weakened backplate?
25th May 2018 8:49 pm
Henda
Member Since: 05 May 2016
Location: Gateshead
Posts: 473
It's got a new back plate on so all good there
I am thinking maybe the cable has unattached from the shoe on the rebuild but it's not worth stripping until the new discs arrive .the problem has to be there once fitted will see if works without further investigation
Thanks for your interest hopefully an easy fix haha it's a disco ,was hoping to just flick a switch and hey presto
CheersAll transmission oil replaced
3 flash indicators
All timing belts changed
EPB serviced
De cat fitted
Wind deflectors
De-tango done
Tints fitted
Egr blanked
25th May 2018 9:14 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4655
Yeah I was going to say something must have come off at the shoe, or expander slipped. No press button solutions on these babies. Once you stripp it it aill likely be obvious
25th May 2018 10:52 pm
Henda
Member Since: 05 May 2016
Location: Gateshead
Posts: 473
My thoughts exactly
Let you all know my progress
Cheers All transmission oil replaced
3 flash indicators
All timing belts changed
EPB serviced
De cat fitted
Wind deflectors
De-tango done
Tints fitted
Egr blanked
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
