Member Since: 08 Mar 2007
Location: Near Basel
Posts: 762
Fitting RRS Badges
Tried to fit the RSS badges. Don't get the rear one off with a screwdriver. Scared to damaged something. Front one: Is there really no other way then make hole with a drill to get it out?
If you get the disc off the plastic surround you can then put it over the existing badge on the grill. It sits slightly proud but looks ok.Loving the power of the TDV8!
Screw the tip of a small flat blade screwdriver a few mm into the centre of each badge and then lever them outThe End
29th Nov 2007 10:56 am
heapster
Member Since: 21 Sep 2007
Location: Sussex
Posts: 257
Liberal amounts of white spirit around the edges to loosen the glue, mask round the surrouding plastic and use a Stanley knife to get behind the metal backing of the original badge.
For some reason the front had stickier glue than the rear....worth getting the metal backing off as the front badge sits nicely flush with the surface.
Sounds a bit long winded to me the chances of getting them out in one piece are pretty slim so just rip them out. I don't think the front is any 'stickier' it's just stuck on a more adhesive surface, paint at the front and plastic at the rear
They fit flush (assuming you've removed all the old ones) without removing the metal backsThe End
29th Nov 2007 11:10 am
StuRox
Member Since: 16 Mar 2007
Location: Wherever the beaten track takes us
Posts: 637
To be honest, I just drilled the front badge with a small drill - as its a plastic grille - no chance of rust etc, and then job is done without any fuss and possibility of scratching the paint off the grille when trying to remove the badge and you will never see the hole again
29th Nov 2007 12:51 pm
RichIFA
Member Since: 22 Oct 2007
Location: North Wales
Posts: 1
RRS Badges
I put the car in the garage and "borrowed" the wife's hairdryer. I only needed to heat the old green badges for around 30 to 45 seconds and they literally fell off. Helps the new ones to stick well if you're well prepared in advance with new labels peeled. A fine electricians screwdriver and a little masking tape will seal the deal.
29th Nov 2007 10:17 pm
Q8LR3
Member Since: 03 Feb 2008
Location: Kuwait City
Posts: 2
Re: RRS Badges
Can you go into a little more detail about how the badges are changed out,i have them already and didn't do anything with them fearing paint damage. you literally blow dried them and they fell out, then you just popped the new black ones right in? no fuss?Keeping it dusty in the desert
4th Feb 2008 11:52 am
Valleyforge
Member Since: 16 Nov 2006
Location: Westmorland actually
Posts: 188
Mate of mine changed the badges on his Ford a bit back, the insert, just glued in, was the correct oval size & shape, the right shade of blue, had the same script & even four letters. What did it say ? It said fart
Why would you want to change ?
6th Feb 2008 11:52 am
CFB
Member Since: 02 Dec 2005
Location: Bradford, West Yorkshire
Posts: 6100
The change is dead easy, as others say just drill or cut the centre of the badge then prise off with a screwdriver, you won't damage the edges then. New ones stick straight on. Airbag one is a bit tricker but not that taxing.
I swapped out all mine for black and silver and they look 8) IMHO.
2020 BMW X1 18d XDrive X-Line Auto
6th Feb 2008 12:23 pm
ronp
Member Since: 29 Nov 2006
Location: North Yorkshire
Posts: 15213
cotefarmboy wrote:
I swapped out all mine for black and silver and they look 8) IMHO.
Agree, looks good Andy, especially on Silver [and Java]
Have you done the door cards yet?🏴
6th Feb 2008 12:36 pm
Valleyforge
Member Since: 16 Nov 2006
Location: Westmorland actually
Posts: 188
Agreed, that actually looks pretty good on your silver Disco.
Thanks for the pic.
6th Feb 2008 1:15 pm
CFB
Member Since: 02 Dec 2005
Location: Bradford, West Yorkshire
Posts: 6100
Badges in my door cards are bigger then the ones in the kit so can't do it.
Not fussed TBH as they are black anyway2020 BMW X1 18d XDrive X-Line Auto
6th Feb 2008 6:20 pm
ronp
Member Since: 29 Nov 2006
Location: North Yorkshire
Posts: 15213
cotefarmboy wrote:
Badges in my door cards are bigger then the ones in the kit so can't do it.
steering wheel badges!🏴
6th Feb 2008 6:26 pm
CFB
Member Since: 02 Dec 2005
Location: Bradford, West Yorkshire
Posts: 6100
Then The Large One has supplied the wrong badges in my kit maybe???2020 BMW X1 18d XDrive X-Line Auto
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum