Member Since: 14 Oct 2005
Location: Somerset
Posts: 1145
I have found that I have had plugs break at 30Nm with the vibro gun.
Regards
Steve
27th Jan 2019 9:11 pm
mek
Member Since: 18 Mar 2015
Location: Zurich
Posts: 469
For what it's worth I contacted Laser to ask about what effects an airline with under 80PSI pressure (recommended min) would have, and received this reply:
Hello Andrew,
You are correct in that the lower the input pressure equals the output torque.
I believe this tool will give you the best chance in removing a glow plugs that could be stuck in by corrosion or carbon build up.
We have not known anyone to break a glow plug with this tool on 4 but it is possible if the corrosion on the plug is bad.
I personally found it best on 4 and once the plug starts to unwind go forward and backward so the impact vibration works on the cause until its removed.
Then obviously the glow plug aperture needs vacuuming and preparing ready for the new plugs.
We cannot guarantee this tool will remove all plugs or even damage plugs but it will be your best option I believe.
Kind regards
Ryan Brookes
Technical Support Manager
29th Jan 2019 6:29 pm
dutchviking
Member Since: 07 Oct 2011
Location: Oslo
Posts: 60
Well good to read that writing this 'how to' does encourage people to take on the job
Would be interesting to learn why some have a lot of carbon deposits on the glow plugs and some not. Is it the quality of the diesel? The ones I removed were only ever so slightly corroded at the top, so near the part that is visible outside the cylinder heads. 2nd and third thread from the top. On the piston side they were all pretty clean.
Here in Norway we use winter diesel almost 6 months a year and pre-heat the engine with the webasto before starting. But I hear about breaking glow plugs as well so not sure.
5th Feb 2019 9:03 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10562
The carbon usually builds up along the length of the glowplug (and they are long) and they aren't perfectly straight.
So when you go to turn them, they hit carbon and go tight.
5th Feb 2019 6:47 pm
vegar
Member Since: 08 Apr 2015
Location: Fredrikstad
Posts: 45
Glødepluggverktøy
Hei.
Ser du har gjort jobben med å bytte glødeplugger, og at du kjøpte verktøy til dette. Hadde det vært mulig å leie det verktøyet av deg?
Mvh
Vegar-05 Disco3 TDV6 SE
-10 Alfa Romeo Mito Q.V.
-84 Autobianchi A112 Abarth
-71 Fiat 127
-68 Austin Mini 1000
4th Jan 2024 10:53 am
ostosix
Member Since: 19 Mar 2017
Location: Lincoln
Posts: 311
Just started glow plugs and havent got the vibro tool. Done glow plugs before on other vehicles without. So i was exceptionally careful. Despite this being ever so careful going back and forth etc, penetrating oil and heating a small socket up to sit over the plugs ive still broken 5 of the 6 plugs. They all nudged with a little click so just kept going both ways and still bust. Only one is out but still coked in.
Either get the tool or tackle these way before they’ve been in 19 years!
1st Feb 2024 6:24 pm
dutchviking
Member Since: 07 Oct 2011
Location: Oslo
Posts: 60
an update after some years.. as part of an engine rebuild I was going to remove the glow plugs while I had both cylinder heads off. 2 days with KROIL presoaking, the vibro impact tool... this time 5 of 6 plugs snapped. Used a glow plug extractor kit but still a time consuming job even with the heads off! What worked even better than the extractor tool was to drill all the way til you see the glow pin stepping up drill diameter from 5 - 5.5 - 6 - 6.5 - 7 - 7.5mm keeping the correct angle. Then it was really easy to get the remaining part out with threads still intact. But then again the heads were off. I bought both heads from a salvage company in the netherlands. They came from a very low milage Range Rover Sport. Might be the different diesel, not several months with winter diesel to cope with low temperatures as we use here in Norway and the fact that I mix the diesel with Liqui Moly 2 stroke oil.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum