Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
DISCO3.CO.UK > Maintenance & Mods (D3)

Door cladding seal fit
Post Reply  Down to end
Page 1 of 1
Lrsg
 


Member Since: 10 May 2020
Location: Norway
Posts: 77

Norway 2008 Discovery 3 TDV6 HSE Auto Zermatt SilverDiscovery 3
Door cladding seal fit

One rear door cladding seal part no CGE500420 was missing on my Discovery 3. I bought a new one, but it does not come with the mounts to fasten the screws. The seal has four screws and I am missing the four plastic mounts which sit behind the seal to attach the screws. Any ideas where these may be obtained? Or an alternative method of fastening? Gluing is not good option.
  
Post #214647916th May 2020 8:31 am
View user's profile Send private message View poster's gallery Reply with quote
kajtzu
 


Member Since: 10 Aug 2017
Location: Helsinki
Posts: 6538

Finland 2005 Discovery 3 4.4 V8 HSE Auto Cairns BlueDiscovery 3

Have you tried looking up it with lrcat? Maybe the mount is one of the small parts in this diagram? http://new.lrcat.com/#!/12128/46398/46889/3686/46968
  
Post #214648216th May 2020 9:10 am
View user's profile Send private message View poster's gallery Reply with quote
Lrsg
 


Member Since: 10 May 2020
Location: Norway
Posts: 77

Norway 2008 Discovery 3 TDV6 HSE Auto Zermatt SilverDiscovery 3

Thanks for the tip. Can't find any fixings on that drawing that looks like the ones I would need. It looks like they may be integral to the wheel arch trim on the door frame. But there is no trace of them on the right side door trim on my car, strangely enough. I could probably cut four soft rubber blocks and glue them on, and fasten the screws in the blocks.
  
Post #214658016th May 2020 6:20 pm
View user's profile Send private message View poster's gallery Reply with quote
Lee Trinder
 


Member Since: 12 Aug 2018
Location: Henley in arden
Posts: 515

2007 Discovery 3 TDV6 HSE Auto Stornoway GreyDiscovery 3

Do you have a picture of the seal on the other door?
If it’s the bit I’m thinking of I’m sure it screws into the arch moulding on the door
  
Post #214658216th May 2020 6:23 pm
View user's profile Send private message View poster's gallery Reply with quote
Lrsg
 


Member Since: 10 May 2020
Location: Norway
Posts: 77

Norway 2008 Discovery 3 TDV6 HSE Auto Zermatt SilverDiscovery 3

This is the upper one


And the lower one

  
Post #214659316th May 2020 7:03 pm
View user's profile Send private message View poster's gallery Reply with quote
Lrsg
 


Member Since: 10 May 2020
Location: Norway
Posts: 77

Norway 2008 Discovery 3 TDV6 HSE Auto Zermatt SilverDiscovery 3

These fixings are missing on the right door, and this is where the rubber seal is attached by screws.
  
Post #214659516th May 2020 7:13 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site