Member Since: 08 Nov 2012
Location: Kent
Posts: 331
Tested mine today after it lost all its charge over the winter.
Nitrogen test, lost 3 bar in 2 hours.
Sprayed soapy water over everything, good soaking, found 2 leaks on condenser.
Viewed from front of car, lower left and upper left area.
New condenser on order. Then need to find a reasonably priced re-fill service.
Click image to enlarge
Click image to enlarge
Click image to enlarge
Click image to enlarge
New Engine - Fitted with body on...
Developer of the FBH Smart Control Module - Keyfob 3rd button control + USB Diagnostics + remote status LED + priming + battery protection + water temp control setpoint (or fixed run time)
I also went for the Nissens brand. £120.New Engine - Fitted with body on...
Developer of the FBH Smart Control Module - Keyfob 3rd button control + USB Diagnostics + remote status LED + priming + battery protection + water temp control setpoint (or fixed run time)
Member Since: 15 Jan 2016
Location: GL
Posts: 10754
New one
6th Jul 2024 8:10 pm
DN D3 Decade
Member Since: 23 Jun 2006
Location: W.London.
Posts: 2346
Be aware, that I and others discovered, that at least 1 of the 2 ‘O’ rings supplied with the Nissens condenser was not the right size.D3 owned from new, P017 brake recall, BAS FBHIC, new FBH, LR013487 oil pump, new water pump. RRS front lower suspension arms. New suspension compressor/ relay. New Denso alternator. CuNifer rear brake pipes. New GKN rear propshaft. New HPFP belt & tensioner. New A/C Condenser.NO WARRANTY for many many years.
Last edited by DN on 6th Jul 2024 10:42 pm. Edited 1 time in total
6th Jul 2024 8:19 pm
discostick
Member Since: 08 Nov 2012
Location: Kent
Posts: 331
Thank you, i will watch out for that.New Engine - Fitted with body on...
Developer of the FBH Smart Control Module - Keyfob 3rd button control + USB Diagnostics + remote status LED + priming + battery protection + water temp control setpoint (or fixed run time)
Member Since: 08 Nov 2012
Location: Kent
Posts: 331
Just changed it out. Not bad at all. The two T40 bolts that are positioned on their own were very corroded in, as many suggest. A good soak with deblock oil (the best i've found for seized bolts by far) and careful loosen-tighten-loosen sequences and they came out fine, but were Very tight.
THe O-rings with the unit were not correct, i purchased new seals by the LR PN#. Althought the originals looked in fine condition.
Other than that, a nice easy job, new condenser on pressure test now. Re-gas booked in for next week, a mobile guy came recommended (Kent-Sussex area) for £45, which is great.New Engine - Fitted with body on...
Developer of the FBH Smart Control Module - Keyfob 3rd button control + USB Diagnostics + remote status LED + priming + battery protection + water temp control setpoint (or fixed run time)
Member Since: 01 Mar 2024
Location: Wisbech
Posts: 72
I did my condenser on my D3 a couple of days ago. Drivers t40’s came out ok. Passenger side however I had to work them in and out very gently a tiny amount to get them to move. Even then I sheared off the T40 but I was using! Ended up using the impact one I had on a long handled ratchet.
The bottom two rails fell off my condenser so god knows how long it’s not had gas in for
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
