Member Since: 01 Jun 2015
Location: Fife, Scotland
Posts: 284
Anyone seen this connection on FBH?
Trying to fit Altox controller today, found this attached to FBH loom....
Anyone seen this connection?
The red (with black stripe) looks like it goes to pin 2
Not sure where the black goes....
Shall I use this to connect?
Cheers
7th Jan 2018 12:20 pm
zinke
Member Since: 22 Feb 2014
Location: Scunthorpe
Posts: 584
Can you check with a meter to see if they are actually connected and not just the same colour wires? And check if the black wire is a earth wire. It could be from a previous controller installed if it is connected to the heater.IID, webasto software and workshop facility's available.
7th Jan 2018 12:44 pm
Coo
Member Since: 01 Jun 2015
Location: Fife, Scotland
Posts: 284
Yeah, need a paper clip to get into plugs..
Cheers
7th Jan 2018 12:47 pm
Bodsy Site Sponsor
Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361
Ignore the two pin connector. Pretty sure that’s transit relay.
You connect to the red wire of the Fbh plug so cut it as long as you can from the Fbh plug and join the blue wire from the Altox to it.Bodsys Brake Bible
Clock/ SNOTM /3Flash / 4x4Info /BT Update /Service Reset/Error Codes / Gearbox Reset See It Here
7th Jan 2018 2:31 pm
Coo
Member Since: 01 Jun 2015
Location: Fife, Scotland
Posts: 284
Yeah, couldn’t even try to test continuity in that plug.
Wired to pin 2 now.
Is there any reason why the unit can’t sit in engine bay?
Cheers!
7th Jan 2018 2:58 pm
PaulJC
Member Since: 07 Mar 2015
Location: Herts / Essex
Posts: 192
Moisture, it's not a sealed unit, so while it may be fine under the bonnet it's safer to mount it in the car.
7th Jan 2018 3:27 pm
zinke
Member Since: 22 Feb 2014
Location: Scunthorpe
Posts: 584
I’ve fitted mine under the bonnet for now, will run the wires into the cab at some point but the fuse box isn’t sealed and that is ok in there.
Pete.IID, webasto software and workshop facility's available.
7th Jan 2018 8:02 pm
Coo
Member Since: 01 Jun 2015
Location: Fife, Scotland
Posts: 284
Same here, shoved it into fuse/battery box until I know it works.
Now at the activate sim point....but will do that tomorrow.
Cheers!
7th Jan 2018 8:48 pm
dgardel
Member Since: 03 Nov 2009
Location: Greater Venice
Posts: 2025
Re: Anyone seen this connection on FBH?
This one is the connector for the Parking heater full kit (when ordered from the origin with the car)
The valve is 18B506
The full kit include the valve and same hoses
Click image to enlarge
- W/O full parking heater kit, hoses 18472C
- With full parking kit, Hoses 18472B + 18472A and valve 18B506Discovery 5 tdv6 HSE Corris Gray Outback Engineering Limited Edition IID Pro MV License
7th Jan 2018 11:03 pm
Coo
Member Since: 01 Jun 2015
Location: Fife, Scotland
Posts: 284
Update:
Altox controller fitted and working...... if only the FBH was behaving itself !!!
Rather than dismantle and try and fix the fbh...
I've got one coming from car breakers, a 2014 one, so should be good!
The controller works though, great communications in that it sends texts if it fails etc.
Pretty easy to set up.
The GPS location part is fantastic!...so tempting to check that car is where I parked it!
Not tried to see what it does when moving, will save that for next time the wife borrows it !!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
