Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
DISCO3.CO.UK > Technical (D3)

2.7 valve timming
Post Reply  Down to end
Page 1 of 1
James1974
 


Member Since: 23 Nov 2017
Location: Stevenage
Posts: 990

United Kingdom 2010 Discovery 4 3.0 TDV6 XS Auto Barolo BlackDiscovery 4
2.7 valve timming

Just wondered if someone can help

Done the timming belt on my car a while ago but it has a tapping noise which is worse when cold for a couple of miles but today I had the cover off the engine when warm and does sound tappy even when warm although not as bad I put a screw driver to each injector and put my ear to it and they all going tap tap tap quiet loud though the screw driver

My question is Is that how it should sound being a diesel or could the valve timming be a fraction out I only used a mark on bottom crank and the two pins on cams and although the crank never
Moved could it still be a tad out as there and intermediate cam shaft that doesn’t have to be a tooth out although it seems to drive ok as I done the belt as soon as I got it I don’t know really if it was like it before

Any advise would be great
  
Post #190127014th Jan 2018 11:57 am
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10360

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

Early cars had "blankets" over the injectors to keep up quiet.

A small piece of black foam each side of the engine.

I doubt its the timing.
  
Post #190128214th Jan 2018 12:15 pm
View user's profile Send private message View poster's gallery Reply with quote
James1974
 


Member Since: 23 Nov 2017
Location: Stevenage
Posts: 990

United Kingdom 2010 Discovery 4 3.0 TDV6 XS Auto Barolo BlackDiscovery 4

There nothing round the injectors and when I was listening around the rear left injector that’s the loudest sounds really load up close but as I never heard another engine running I don’t really know how quiet/loud the engine should be
Wasn’t sure on the timming as there is plenty of power and I’m sure with a diesel being the slightest out surely it wouldn’t run right as it needs compression to ignite the fuel and if it was out a tad then it wouldn’t have the compression it needs

I wonder if anyone on here could post a video of there’s so I can compare it
  
Post #190128414th Jan 2018 12:20 pm
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10360

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

you can see the blankets on this one.

http://www.ebay.co.uk/itm/LAND-ROVER-DISCO...SwxzdaPMvT



I understand later engine are also more noisy. I think its that way round
  
Post #190129714th Jan 2018 12:32 pm
View user's profile Send private message View poster's gallery Reply with quote
James1974
 


Member Since: 23 Nov 2017
Location: Stevenage
Posts: 990

United Kingdom 2010 Discovery 4 3.0 TDV6 XS Auto Barolo BlackDiscovery 4

Yes I have one of them blankets on the right bank but not the left and yes mine is a 2009 58 plate so one of the last ones made
  
Post #190130714th Jan 2018 12:54 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site